Development kit with WiFi and Bluetooth module ESP32-WROVER

Development board with WiFi and Bluetooth ESP32 module. It has been equipped with industrial interfaces RS485 and CAN. TTGO T-CAN485 ESP32

Module with a 4-inch touch display that uses two MCU systems (ESP32-S3 and RP2040) and supports Wi-Fi, BLE and LoRa communication. The board is equipped with USB Type C, I2C (Grove) and analog inputs interfaces and can easily connect to other peripheral devices. Seeed Studio 114993070

Board with WiFi Espressif ESP32-S2 module and u.FL connector. It offers 4 MB of Flash memory and 2 MB of SRAM and an RGB LED. It is equipped with a STEMMA QT connector. Adafruit 5348

A board with an ESP32 module equipped with a 1.28-inch round display. It offers Wi-Fi and Bluetooth 5.0 communication and has a built-in 6-axis QMI8658 IMU sensor and supports charging lithium batteries. Perfect for developing IoT, mobile devices and wearable electronics projects. Waveshare ESP32-S3-LCD-1.28

Beetle ESP32 is a small (35 × 34mm) board thanks to which the creation of the Internet of Things (IoT) is very simple. The module was based on the ESP32 system, which allows for Bluetooth communication (compatible with Bluetooth 4.2) and WiFi. DFRrobot DFR0575

Small AI development board based on ESP32-S3 SoC with integrated WiFi 802.11 b/g/n and BLE transceiver. It has a built-in 2 MP camera, LCD display and microphone. Espressif ESP32-S3-EYE

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripheral devices - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, fast SPI, UART, I2S and I2C. SparkFun WRL-17381

Development board based on a microcontroller with a RISC-V core. It offers support for WiFi 6, Bluetooth 5 and Zigbee 3.0 and Thread (IEEE 802.15.4) protocols. It uses the ESP32-C6-WROOM-1-N8 module and is compatible with ESP32-C6-DevKitC-1-N8. Waveshare ESP32-C6-DEV-KIT-N8

Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. With DC adapter and Li-Ion battery. Totem TE-X4-KIT3

Development board designed for IoT projects. It is equipped with a WiFi/Bluetooth module ESP32, LoRa 868 MHz, GPS and a basket for a Li-Ion 18650 battery. TTGO T-Beam V1.1

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5399

Module with WiFi and Bluetooth Espressif ESP32 WROOM. It integrates a set of peripherals - capacitive touch sensors, Hall sensors, SD card interface, Ethernet, SPI, UART, I2S and I2C. SparkFun WRL-20168

Development board designed for IoT projects. It is equipped with a WiFi/Bluetooth module ESP32, LoRa 433 MHz, GPS and a basket for a Li-Ion 18650 battery. TTGO T-Beam V1.2

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

The low-power consumption micro-controller intentionally designed for Internet of Things (IoT) projects. The board integrates a Dual-Core ESP-WROOM-32 module, which supports MCU and Wi-Fi &Bluetooth dual-mode communication. DFR0478

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. Adafruit 5398