DFRobot ESP8266 Wifi Bee module for Arduino
ID: 561322
5902186311916
zł30.37
Tax included
zł24.69 tax excl.
WiFi wireless communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The product is compatible with Arduino. DFRobot TEL0092
Description
ESP8266 Wifi Bee is a wireless WiFi communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The board has a switch that can be used to easily select the starter mode or software update mode. The product is compatible with Arduino .
The module is based on the ESP8266 chip with a 32-bit microcontroller. It has a built-in Lwip protocol stack. The module configuration is carried out using AT commands.
Attention!
In order to configure the module, you need an Xbee USB adapter . It is not included in the kit and must be purchased separately.
In order to configure the module, you need an Xbee USB adapter . It is not included in the kit and must be purchased separately.
properties
- Wi-Fi Direct (P2P), soft-AP
- Built-in TCP / IP protocol stack
- 32-bit low power processor
- Support for WPA2 / WPA2-PSK WPA encryption
- UART interface support
- Support for TTL serial port in a wireless application
- Wireless standard: IEEE 802.11b / g / n
- Frequency: 2.4 GHz
- Operating voltage: 3.3 V
561322
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
WiFI 802.11 b/g/n module. Equipment includes, among others: LED diode, antenna, 8 pins with 2.54mm pitch (including 3 GPIO lines). Power supply: 3.3V.
zł10.41
24h
Available quantity: 20
Available
WiFi 802.11 b/g/n module with ESP8266 system, 16 terminals are available with a 2 mm pitch with the possibility of soldering gold pins, there are 9 GPIO lines and 1 ADC line on the connector. Built-in ceramic antenna and U.FL antenna connector. ESP-07
zł11.50
24h
Available quantity: 71
Available
Development board ESP8266 with WiFi module; WRL-13231
Regular pricezł127.80zł69.62
24h
Available quantity: 5
Available
Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05
zł16.06
24h
Available quantity: 20
Available
Available
Xbee USB adapter based on the FTDI chip. Intended for configuring Xbee modules. Thanks to the female goldpin connector, it can be used as an FTDI programmer for Arduino FIO / pro / mini / lilypad. DFRobot DFR0050
zł81.45
24h
Available quantity: 2
Available
Other products in the same category (16)
Development board ESP8266 with WiFi module; WRL-13231
Regular pricezł127.80zł69.62
24h
Available quantity: 5
Available
Easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ‘widgets’ within the Blynk mobile app to create your next IoT project. WRL-13794
zł188.04
24h
Available quantity: 2
Available
ESP8684-DEVKITC-02C-N4 is a development board with the ESP8684 module, 4 MB Flash, Wi-Fi, and Bluetooth LE support, perfect for IoT and automation projects. Espressif ESP8684-DEVKITC-02C-N4
zł59.90
24h
Available quantity: 2
Available
WiFi module with ESP8266 designed to work with the Raspberry Pi Pico. It communicates via the UART interface using AT commands. Waveshare Pico-ESP8266
zł41.62
24h
Available quantity: 4
Available
Wifi module with ESPR8266 ESPRESSIF for communication in the 2.4 GHz band. It is powered by a voltage from 3 V to 3.6 V, available in an SMD enclosure. ESP-WROOM-02
zł15.66
24h
Available quantity: 4
Available
ESP-PROG is an advanced tool for programming and debugging Espressif microcontrollers such as ESP32, ESP32-C3, ESP32-S2, ESP32-S3 and ESP8266. With the built-in FT2232HL USB bridge, ESP-PROG converts the USB 2.0 interface to serial and parallel interfaces, offering functions of automatic firmware download, serial communication and online debugging via JTAG
zł80.90
1 weeks
No product available!
The module is based on the ESP8266MOD chip. Thanks to the support of the 802.11 b/g/n standard, it enables wireless communication with WiFi networks, which allows for Internet access and data exchange. WeMos D1 Mini Type-C
zł15.62
24h
Available quantity: 59
Available
WiFi module with ESP8266 and 1.14" display, designed to work with Raspberry Pi Pico. It communicates via UART interface using AT commands. SB Components 21888
zł75.50
24h
Available quantity: 2
Available
Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini
zł19.36
24h
Available quantity: 19
Available
Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x
zł18.70
24h
Available quantity: 33
Available
Development board with ESP8266 microcontroller with built-in Wi-Fi communication. The system is clocked at 80 MHz and powered by 3.3 V. It includes a Tensillica core and a full Wi-Fi stack. Adafruit 3046
zł111.73
24h
Available quantity: 2
Available
Evaluation set designed for the use of Internet of Things based on ArduCAM-Mini-2MP and ArduCAM-ESP8266-Nano-V2 modules. ArduCAM-Mini-2MP is a module with a 2 megapixel camera with an OV2640 transducer and an ESP8266 chip. Mounting the M12 lens. ArduCAM B0085
zł234.47
24h
Available quantity: 1
Available
The module is based on the ESP8266EX chip. Thanks to the support of the 802.11 b/g/n standard, it enables wireless communication with WiFi networks, which allows for Internet access and data exchange. It is programmed via the USB Type-C connector using Arduino, MicroPython or NodeMCU. WeMos D1 Mini Type-C
zł14.22
24h
Available quantity: 99
Available
The base board for the Wi-Fi NodeMCU module (ESP-12E), thanks to the built-in L293DD system, allows for attaching e.g. motors, electromagnets or other executive devices. The I/O lines of the NodeMCU module were derived to the pin connectors, and the power supply can be connected with the use of screw connectors. ESP12E Motor Shield
zł7.07
24h
Available quantity: 10
Available
ESP8266 based Arduino board for ArduCAM mini camera modules while keeping the same form of factors and pinout as the standard Arduino UNO R3 board. ArduCAM B0082
zł87.55
4 weeks
No product available!
WiFi 802.11 b/g/n module with ESP8266 chip, there are 8 pins with UART and GPIO interface. Built-in PCB antenna. SparkFun WRL-17146
zł50.02
24h
Available quantity: 2
Available
WiFi wireless communication module compatible with the pin spacing of XBEE modules. The module is powered by 3.3 V. The product is compatible with Arduino. DFRobot TEL0092