

The flame detector module detects the source emitting a wavelength between 760 and 1100 nm. It allows to detect, among others source of fire. The sensor probe has a detection angle of 60 °. When working with the sensor, make sure that the flame is not too close to the sensor, as it may damage it. The sensor has an analog output. The module is equipped with a Gravity connector and supports the Arduino series of boards.
An example of use is available on the product Wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
et with a measuring module and a probe for measuring electrical conductivity. It allows you to measure the salinity of water and soil. It has a Gravity analog output interface. DFRobot DFR0300-H
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
The Gravity Occupancy Sensor uses 24 GHz FMCW radar technology, enabling precise presence detection at a distance of up to 8 meters and movement and distance measurement up to 12 meters. Thanks to its high resistance to environmental interference, it works reliably regardless of light, temperature or dust, effectively detecting both static and dynamic objects. Compatibility with Arduino, ESP32, Raspberry Pi and a simple Gravity interface make it an ideal solution for intelligent lighting, building automation and security systems. DFRobot SEN0610
Module with a miniature DC motor. No additional controller is required to start the engine. The module is controlled by the PWM signal. DFRobot DFR0411
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
A set of 5 modules with a bistable button and LED backlight. The boards are equipped with a Gravity connector and communicate via a digital interface. DFRobot DFR0789
Heart rate measurement module compatible with Arduino and Raspberry Pi (Gravity: Heart Rate Monitor Sensor For Arduino). It uses PPG technique, which in a simple and cheap way is able to measure the changing volume of blood. DFRobot SEN0203
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
Module with digital barometer ICP-10111. The system enables pressure measurement in the range from 300 to 1100 hPa with an accuracy of 1 Pa. DFRobot SEN0517
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Module with an analog MQ2 gas sensor. It enables the detection of LPG, butane, propane, methane, alcohol, hydrogen and smoke. It is powered with the voltage of 5 V and has an analog output. DFRobot SEN0127
The expansion board is designed for DFRduino M0 or Bluno M0 sets. The board has 31 GPIO pins (including 6 PWM and 6 ADC inputs), UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0412
Real time clock (RTC) module DS1307. It is powered by 5 V and communicates via the I2C interface (Gravity connector). There is also a CR1220 battery socket on the board. DFRobot DFR0151
Module with a button and yellow LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-Y
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 5A. DFRobot SEN0287
he flame detector module detects the source emitting a wavelength between 760 and 1100 nm. It allows to detect, among others source of fire. Analog interface. DFRobot DFR0076