 
        
           
        
          Module with a button and green LED backlight. The board is equipped with a Gravity connector and has a digital output. The LED backlight turns on when the button is pressed. The module is supplied with the voltage of 3.3 V or 5 V. Full documentation of the module with examples of use is available on the product Wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Bluno - BLE with Arduino Uno
Switch module with an interlock. DFRobot DFR0423
Educational micro:bit module with 32-bit ARM Cortex-M4 microcontroller. Manufactured to interest the youngest in computer engineering. SparkFun DEV-17287
Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214
Gravity: Vibration Motor Module is a module with a small vibration motor powered by 5V voltage, controlled by a binary signal (high / low state) or using a PWM signal. DFRobot DFR0440
Water pressure sensor with 3-pin Gravity interface. It enables the measurement of liquid pressure in the range from 0 to 1.6 MPa. It is supplied with the voltage of 5 V and has a linear output voltage from 0.5 to 4.5 V. DFRobot SEN0257
Module with an analog light sensor. It consists of a photoresistor and a LED. Equipped with a Gravity connector. DFRobot DFR0022
Soil moisture sensor with analog output. The probe has two pointed tabs, making it easy to insert into the ground. It is supplied with the voltage of 3.3V or 5V. DFRobot SEN0114
 No product available!
This encoders are designed for DFRobot 3PA and AWD Rovers. It can give you the rotation degree of the wheels. Encoder uses non-contact method to convert the angular displacement signals. Best fit with Micro DC Geared Motor. SEN0038
Flexible 16x16 RGB LED matrix module. The set uses addressable SK6812/WS2812B diodes. DFRobot DFR0463
 No product available!
An expansion board designed for FireBeetle M0 and ESP32-E kits. The board has 12 GPIO pins, 5 ADC, UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0762
A set with a temperature sensor based on the DS18B20 system in the form of a waterproof measuring probe, a sensor adapter and a cable. Communication via the 1-Wire interface. DFRobot KIT0021
Ring light with 24 RGB diodes WS2812B type controlled by serial signal. The module can be powered with the voltage from 3.3 V to 5 V, only one signal line is required to control it. DFRobot DFR0888-24
Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251
 No product available!
PIR motion sensor module for Arduino and Raspberry Pi. DFRobot SEN0018
The infrared distance sensor enables the detection of objects in the range from 3 to 50cm. The sensor has a digital output, the detection threshold is adjusted by a potentiometer. DFRobot SEN0164
Module with 6-axis BMI160 motion sensor (accelerometer and gyroscope) with 16-bit data resolution. It is supplied with the voltage in the range from 3.2 to 6 V. I2C communication. DFRobot SEN0250
The arduino turbidity sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. SEN0189
 
                    Module with a button and green LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-G