TE0790-03 - XMOD FTDI JTAG adapter (Xilinx compatible)
ID: 577317
zł321.17
Tax included
zł261.11 tax excl.
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART. Compatible with Xilinx tools. Trenz TE0790-03
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART.
The module is equipped with a programmable CPLD system controller supplied by Lattice XO2-256 CPLD to control the signals of configured interfaces. The USB 2.0 data stream can also be converted to 8 independent GPIOs or used as FIFO.
EEPROM is pre-programmed and recognized by all Xilinx tools (ISE / Impact / Chipscope, Vivado Programmer / SDK).
Features
- FT2232H
- RX / TX channel LEDs
- Mini USB connector (no cable included)
- 93C56 EEPROM
- Lattice XO2-256 CPLD
- Programmable with Lattice tools
- 8 universal I / O pins
- VCCIO or 3.3 V or supplied by the user (1.8 to 3.3 V)
- Red user LED
- 12 MHz clock with oscillator
- DC / DC step down converter for USB power supply
- Green power LED
- User Button
- 4-position DIP switch
- Selecting the CPLD program mode
- Disabling FTDI EEPROM
- VIO as VCC
- VCC with USB
- Dimensions: 20 x 25 mm
- M3 mounting holes
577317
You might also like
Adapter for 20/14/10-pin JTAG. It allows to connect the JTAG programmer to a evaluation boards which uses various standards of the programming connector. IDC20, IDC14, IDC10 and JST-XH sockets are available.
zł8.94
24h
Available quantity: 18
Available
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
zł399.00
24h
Available quantity: 47
Available
Module with Xilinx Kintex-7 XC7K70T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-070-2CF
zł1,344.00
Delivery date unknown
No product available!
Module with Xilinx Kintex-7 XC7K160T-2IF chip, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-03-160-2IF
zł2,863.60
Delivery date unknown
No product available!
Module with Xilinx Kintex-7 XC7K325T-2CF system, 32MB FLASH memory and very fast data transmission systems. Everything is on a small 4 x 5 cm plate. TE0741-02-325-2CF
zł2,950.12
Delivery date unknown
No product available!
Other products in the same category (3)
Adafruit 2094 - JTAG (2x10 2.54mm) to SWD (2x5 1.27mm) Cable Adapter Board
zł24.13
24h
Available quantity: 24
Available
Adapter for 20/14/10-pin JTAG. It allows to connect the JTAG programmer to a evaluation boards which uses various standards of the programming connector. IDC20, IDC14, IDC10 and JST-XH sockets are available.
zł8.94
24h
Available quantity: 18
Available
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
zł399.00
24h
Available quantity: 47
Available
Universal USB2.0 adapter for JTAG, UART and GPIO based on the FTDI FT2232H chip. The adapter card converts signals from USB2.0 to standard serial or parallel interfaces of embedded systems such as JTAG, SPI, I²C and UART. Compatible with Xilinx tools. Trenz TE0790-03