STEMMA QT Arcade Button 1x4 - module for arcade buttons
ID: 1178260
5906623430932
zł58.49
Tax included
zł47.55 tax excl.
The module allows you to connect 4 arcade buttons with LED backlight. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5296
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The module is dedicated to operate four arcade buttons. It is equipped with 8 JST XH sockets, to which buttons with LED backlight can be connected. The built-in microcontroller is pre-programmed, thanks to which the reading of button presses and the PWM LED control is done via the I2C bus. The module is powered with the voltage from 3.3 V to 5 V, and communication is via the STEMMA QT connector. Full documentation is available on the product page.
Features
- 8 x JST XH 2.54 mm connectors
- Possibility to connect 4 buttons with LED backlight
- Communication: I2C (address 0x3A)
- STEMMA QT (Qwiic) connector
- Power supply: 3 to 5V
- Dimensions: 76.3 x 21.5 x 13 mm
Kit contains
- STEMMA QT Arcade Button 1x4
- 12-pin goldpin male connector
1178260
You might also like
No product available!
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
zł9.64
24h
Available quantity: 2
Available
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
zł10.55
24h
Available quantity: 9
Available
Other products in the same category (16)
Module with a button and yellow LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-Y
zł23.16
24h
Available quantity: 2
Available
Module with a button, LED diode and a yellow cap. DFRobot DFR0029-Y
zł8.87
24h
Available quantity: 1
Available
Module with AT42QT1060 controller - contectless keyboard controller, Kamami, RoHS.
zł89.00
24h
Available quantity: 185
Available
Keyboard module with five colored buttons. The board is equipped with a Gravity connector and has an analog output. Powered with the voltage of 3.3 V or 5 V. DFRobot DFR0075
zł23.91
24h
Available quantity: 2
Available
Module with a button, LED diode and a white cap. DFRobot DFR0029-W
zł8.68
24h
Available quantity: 1
Available
Available
Module with a bistable button and blue LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-B
zł21.00
24h
Available quantity: 2
Available
No product available!
Two-button module with 4 colored overlays. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020103
zł18.75
24h
Available quantity: 4
Available
Switch module with an interlock. DFRobot DFR0423
zł9.84
24h
Available quantity: 7
Available
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
zł8.68
24h
Available quantity: 4
Available
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
zł19.90
24h
Available quantity: 447
Available
Module with a bistable button and white LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-W
zł21.00
24h
Available quantity: 2
Available
Membrane keypad module with 12 (3x4) buttons. It is equipped with a tape terminated with a 7-pin connector
zł5.17
24h
Available quantity: 6
Available
Module with a bistable button and green LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-G
zł21.00
24h
Available quantity: 2
Available
Module with a button and red LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020044
zł13.68
24h
Available quantity: 2
Available
The module allows you to connect 4 arcade buttons with LED backlight. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5296