Keyboard module with 10 tact switch buttons. The output of each button has been led to pins with a 2.54 mm raster together with GND reference pins, which allows the board to be used to control other modules with digital inputs, eg DFPlayer Mini or Voice Recorder without additional adapters. In addition, the buttons together with appropriately selected resistors form a matrix that can be connected to the analog pin of the microcontroller. The set includes dedicated caps to facilitate the use of the keyboard. Full documentation with application examples is available on the product wiki page.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Cables for evaluation boards, set of 10 pcs., blue colour
Cables for evaluation boards, set of 10 pcs., red colour
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
A set of 10 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-10-17)
Gravity: Voice Recorder Module is a sound recording module powered by 5V voltage. It can store sounds up to 10 seconds long. DFRobot SEN0197
Mini MP3 player with microSD card support. It can work as a separate device and play sounds from the card or be controlled via the UART serial interface. DFRobot DFR0299
No product available!
Gravity: Joystick Module V2 is a joystick module with two analog outputs (X and Y axis) and a digital output (Z axis) supplied with 3.3 ... 5V voltage. DFRobot DFR0061
Mini keyboard with 16 buttons and RGB backlight. Equipped with a connector compatible with Grove, it communicates via the I2C interface. Adafruit 3954
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
Module with a button and re LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-15932
Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842
Numeric keypad module with 12 buttons. The board has the ATtiny85 microcontroller, which processes data from the keyboard and sends it in a convenient form via the I2C interface. SparkFun COM-15290
No product available!
Module with a button, LED diode and a yellow cap. DFRobot DFR0029-Y
Module with a button, LED diode and a white cap. DFRobot DFR0029-W
Module with a button, LED diode and a green cap. DFRobot DFR0029-G
Module with a button, LED diode and a red cap. DFRobot DFR0029-R
Keyboard module with five colored buttons. The board is equipped with a Gravity connector and has an analog output. Powered with the voltage of 3.3 V or 5 V. DFRobot DFR0075
Module with 12-position rotary switch. It is supplied with the voltage ranging from 3.3 V to 12 V and has an analog output (Gravity connector). DFRobot SEN0156
No product available!
Module with 5 colored buttons. Each button is powered independently and has an output informing about its status
No product available!
No product available!
Universal module for building a keyboard. The set consists of a control board with a miniUSB socket and cables with crocodile clips
The module is equipped with two buttons in red and blue. It communicates via a digital interface and allows you to add simple controls to your M5Stack based project. M5Stack U025
Keyboard module with 10 tact switch buttons. The state of the buttons can be read using digital pins or a common analog output. DFRobot DFR0792