VEML7700 is a high accuracy ambient light digital 16-bit resolution sensor. It includes a high sensitive photo diode, a low noise amplifier, a 16-bit A/D converter and supports an easy to use Gravity I2C interface. It outputs a digital signal directly and no need for complicated calculations. This is a more accurate and easier to use version of the simple photo resistor which only outputs a voltage that needs to be calculated in order to obtain meaningful data. The data which is output by this sensor is directly output in Lux (Lx). When objects which are lighted in homogeneous get the 1 lx luminous flux in one square meter, their light intensity is 1lx. Sometimes to take good advantage of the illuminant, you can add a reflector to the illuminant. So that there will be more luminous flux in some directions and it can increase the illumination of the target surface.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
modTSL2561 is a module containing a light sensor TSL2561; communication with the system takes place using the I2C bus
No product available!
The module allows measuring the light around the sensor. The measuring range is in the range 1 - 65535 LUX, and communication takes place using the I2C bus. modBH1750 (GY-302)
No product available!
Great way to upgrade a project that uses a photocell and needs RoHS compliance. Due to the high rejection ratio of infrared radiation, the spectral response of the ambient light sensor is close to that of human eyes. Adafruit 2748
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
AS7331 UV light sensor module. It allows you to measure UV radiation on three channels: UVA (320-400nm), UVB (280-320nm) and UVC (200-280nm). Communication with AS7331 takes place via the I2C interface and the Qwiic connector. SparkFun SEN-23517
Module with three optical inspection sensors (spectrophotometers) from the AS7265x series. The module consists of three sensors; AS72651, AS72652 and AS72653 which can detect wavelengths from 410nm (UV) to 940nm (IR). SparkFun SEN-15050
TCS34725 RGB Color Sensor is a color sensor TCS34725 controlled by the I2C interface. It is powered by voltage in the range of 3.3 ... 5V and is intended for Arduino-compatible boards. DFRobot SEN0212
Module with a light sensor (photoresistor) designed for M5Stack sets. An analog output and a digital output have been led out on the Grove connector. M5Stack U021
Module with light sensor (photoresistor). An analog output was led out on the XH2.54 connector
Module with color and light intensity sensor. Offers a wide detection range and two LED backlights. It communicates via the I2C bus. It communicates via the I2C bus. Pimoroni PIM375
DFRobot Gravity analog light intensity module for Arduino and Raspberry Pi. DFRobot DFR0026
Module with light intensity sensor TSL2591. Equipped with STEMMA QT connector with I2C interface. Adafruit 1980
Module with an analog TEMT6000 light intensity sensor. The output voltage is linearly correlated with the intensity of the incident light. The module is supplied with the voltage from 3.3 to 5V
Precise solar radiation intensity sensor in the range from 400 to 1100 nm, communicating via Modbus-RTU (RS485) and resistant to harsh conditions thanks to the aluminum housing class IP67. High accuracy (±5%), fast response time (≤10 s) and resistance to dirt make it ideal for monitoring photovoltaics, environmental research and meteorology. DFRobot SEN0640
Sensor for detecting the distance, intensity and frequency of light (lightning) within a radius of 40 km. The module enables weather enthusiasts to measure data about local storms. DFRobot SEN0290
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
A multifunctional module with an optical sensor for measuring the intensity of illumination, the color of the incident RGB light, the distance from the object and the detection of 3D gestures. Detection range from 10 to 20 cm, communication via I2C. SparkFun SEN-12787
Compact module with three I2C sensors, enabling measurement of temperature, humidity, pressure, light, proximity and motion. It offers two Qw/ST connectors, so you can quickly connect it to Raspberry Pi, Pico or other microcontrollers. Ideal for IoT applications, home automation and environmental analysis in mobile or stationary projects. Pimoroni PIM745
SEN0162 This UV Sensor with GUVA-S12SD chip is suitable for detecting the UV raditation in sunlight. It can be used in UV Index Monitoring, DIY project, UV-A Lamp Monitoring, Plants growing Environmental monitoring...etc.
UV Sensor with response spectrum: 200nm-370nm
Gravity: I2C VEML7700 Ambient Light. Sensor SKU. SEN0228