• New
Main view
search
  • Main view
  • Top view
  • Top view
  • Angled view
  • Bottom view
ID: 1210215
zł399.00
Tax included

zł324.39 tax excl.

Development board featuring an ESP32-WROOM-32UE-N4 module and an SX1276 transceiver for LoRa communication at 868MHz. Provides 5 GPIO connections, two Crowtail/Grove-compatible I2C connector footprints, and a prototyping area with a 2.54mm pitch. Supports power via USB-C or a LiPo battery with charging provided by an integrated controller. Features a 7-pin programming interface, two programmable green LEDs, and a U.FL/IPEX antenna connector. Supports the development of IoT nodes using LoRaWAN, Helium, and Meshtastic with compatible firmware. The kit includes a LoRa antenna and two unsoldered 4-pin connectors. HobbyIoT H2S-Dev v1.2 Basic

24h
Available
Available quantity: 2

Description

The H2S-Dev v1.2 Basic development board uses an ESP32-WROOM-32UE-N4 module with a dual-core Xtensa LX6 processor running at up to 240MHz and 4MB Flash memory, along with an SX1276 transceiver for LoRa communication at 868MHz. The board supports the development of wireless IoT nodes, distributed sensor systems, and telemetry devices for environmental monitoring and long-range data transmission.

The ESP32 module also supports 2.4GHz Wi-Fi and Bluetooth 4.2, including Bluetooth LE. The board can operate in LoRaWAN and Helium IoT networks and run Meshtastic firmware for decentralized radio communication. Using a selected solution requires preparing and flashing compatible firmware. The LoRa radio circuit provides a U.FL/IPEX antenna connector for attaching the helical antenna shown in the product photographs.

The board exposes 5 GPIO connections and two Crowtail/Grove-compatible I2C connector footprints. The kit includes two 4-pin connectors that require soldering before use. The board also features a prototyping area with 32 holes arranged in a 4x8 grid with a 2.54mm pitch. Power, ground, and GPIO connections are located nearby. The layout supports the installation of additional sensors, electronic components, and simple measurement circuits without requiring a separate prototyping board.

            

Power is supplied through USB-C or a LiPo battery connected to the dedicated socket. An integrated charging controller supports charging the connected battery, while a battery voltage monitoring line is connected to an ESP32 GPIO. Firmware is flashed through a 7-pin serial programming interface using a compatible USB-to-UART adapter. The USB-C connector is intended for powering the board, while programming is performed through a separate interface.

The board features a RESET button, two programmable green LEDs, and indicators for power and battery charging status. The PCB also provides a footprint for a 40-pin Raspberry Pi interface, but the connector is not factory installed. The Basic 868MHz variant does not include a GNSS receiver. The hardware design is available as an open-source project, including circuit schematics, design files, and software examples for Arduino, Helium, and Meshtastic.

Features

  • Processor and connectivity
    • Model: H2S-Dev v1.2 Basic
    • Microcontroller module: ESP32-WROOM-32UE-N4
    • Processor: dual-core Xtensa LX6, up to 240MHz
    • Flash memory: 4MB
    • Radio transceiver: SX1276
    • Communication technology: LoRa
    • LoRa frequency: 868MHz
    • LoRa antenna connector: U.FL/IPEX
    • Wi-Fi: 2.4GHz, IEEE 802.11 b/g/n
    • Bluetooth: 4.2, including Bluetooth LE
    • Supported solutions: LoRaWAN, Helium IoT, Meshtastic
    • Development environment: Arduino
  • Interfaces and expansion
    • Exposed GPIO connections: 5
    • Crowtail/Grove-compatible I2C connector footprints: 2
    • Crowtail/Grove connectors: 4-pin, unsoldered
    • Prototyping area: 4x8 holes
    • Number of prototyping holes: 32
    • Hole pitch: 2.54mm
    • Power and ground connection points near the prototyping area
    • Programming interface: 7-pin serial interface
    • Programming: via a compatible USB-to-UART adapter
    • RESET button
    • Programmable LED indicators: 2 green LEDs
    • 40-pin Raspberry Pi connector footprint, connector not installed
    • GNSS receiver: not included
  • Power supply
    • Power input: USB-C
    • LiPo battery power support
    • LiPo battery socket: onboard
    • LiPo battery charging controller: onboard
    • Battery voltage monitoring via an ESP32 GPIO
  • Additional information
    • Board version: v1.2
    • Variant: Basic 868MHz
    • Hardware design: open source

Kit Includes

  • H2S-Dev v1.2 Basic 868MHz development board - 1 pc.
  • LoRa helical antenna with cable and U.FL/IPEX connector - 1 pc.
  • 4-pin Crowtail/Grove-compatible I2C connector, unsoldered - 2 pcs.
1210215

Manufacturer

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Responsible person

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Other products in the same category (16)