Micsig RCP600XS - Rogowski AC 600A Current Probe
ID: 1190113
5902186320109
zł4,059.00
Tax included
zł3,300.00 tax excl.
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP600XS
Description
Micsig RCP is a Rogowski-type current probe designed for precise measurement of AC currents while maintaining a wide bandwidth up to 30 MHz. Thanks to its flexible, thin coil with a cross-section of only 1.6 mm, the device is perfect for hard-to-reach areas in electronic circuits, such as the leads of TO-220 transistors or other power semiconductors. The probe introduces almost zero input impedance, minimizing impact on the Device Under Test (DUT). An integrated amplifier powered by 12 V DC enables accurate measurement of highly dynamic, high-frequency signals.
The BNC interface allows for easy connection to any oscilloscope. The device offers a typical accuracy of 2% and excellent resistance to interference and high voltages up to 1 kVrms. The RCP probe is widely used in power electronics research—from switching current measurements in MOSFET and IGBT transistors to power quality analysis in inverters, UPS units, and SMPS systems. Its compact design and customizable coil parameters make it an invaluable tool for R&D labs and diagnostic departments.
Features
- Bandwidth: 10 Hz to 30 MHz
- Rise time: ≤ 11.6 ns
- Maximum current: 600 A (peak)
- Output sensitivity: 10 mV/A (10x mode)
- Typical accuracy: ±2%
- Output noise: < 12 mVpp
- Slew rate: 40 kA/μs
- Signal droop: 6%/ms
- Conductor positioning effect: ±1%
- Offset voltage: < ±1 mV
- Coil insulation: 1 kVrms for 1 min
- Max measured conductor diameter: ≤ 20 mm
- Power supply: DC 12V
- Output impedance: 1 MΩ
- Interface: standard BNC
- CE standards: EN IEC 61010-2-032
- EMC standards: EN IEC 61326-1:2021 and others
- Operating temperature range: base 0°C–55°C, coil –20°C–125°C
- Storage temperature range: –30°C–70°C
- Operating humidity: ≤ 85% RH
- Storage humidity: ≤ 90% RH
- Integrator dimensions: 70 × 40 × 17 mm
- Cable length: 1.5 m (customizable)
- Inner coil diameter: 25 mm (customizable)
- Coil circumference: 80 mm (customizable)
- Coil cross-section: approx. 1.6 mm
1190113
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP300XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP600XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP1200XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP120XS
zł4,182.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP60XS
zł4,182.00
Delivery date unknown
No product available!
Other products in the same category (16)
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 50 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP503B
zł3,431.45
4 weeks
No product available!
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP1000-1G
zł6,599.00
4 weeks
No product available!
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 50 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8050
zł938.99
4 weeks
No product available!
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 800 MHz and 1 GHz frequency band. Micsig OP20-1G
zł6,599.00
4 weeks
No product available!
A probe tip with attenuation factor of 5000X. Dedicated to Micsig probes from the SigOFIT series operating in the frequency band of 100MHz, 200MHz and 350MHz. Micsig OP5000-3
zł3,874.19
4 weeks
No product available!
The Micsig DP series differential probe is based on advanced metal shielding technology. It offers a 200 MHz frequency band and the ability to measure voltages up to 7000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP7002
zł4,499.00
4 weeks
No product available!
The PP80B oscilloscope probe is a reliable tool for precise measurements, compatible with digital and analog oscilloscopes, offering a bandwidth of up to 80 MHz and the ability to select the attenuation factor. Hantek PP-80B
zł23.52
24h
Available quantity: 12
Available
BNC connector cable (adapter) to the "Alligator clip" connector. It allows you to conveniently connect the device, e.g. to an oscilloscope. Digilent (240-134)
zł52.64
24h
Available quantity: 2
Available
LCRkelvin is a four-wire Kelvin probe for precise measurement of RLC components with minimal wire resistance impact. Equipped with gold-plated Kelvin clips, it ensures accuracy and reliability, and its design is compatible with LCR meters from various brands, such as Hantek and Uni-T
zł141.61
24h
Available quantity: 1
Available
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a 300 MHz frequency band and the ability to measure voltages up to 700 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP703
zł4,059.00
4 weeks
No product available!
A set of needle probes used for piercing wire insulation. They can be used as pin probes when working with small PCBs or connectors. Hantek HT307
zł33.12
24h
Available quantity: 10
Available
The probe tip has a 50X attenuation factor. Designed for Micsig probes from the SigOFIT series operating in the 100MHz, 200MHz and 350MHz frequency band. Micsig OP50-3
zł1,398.90
4 weeks
No product available!
Test probe tip with 20X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 350 MHz and 500 MHz frequency bands. Micsig OP20-5
zł4,598.99
4 weeks
No product available!
Oscilloscope probe designed for the analysis of signals generated by the ignition coil in automotive engines. It is compatible with most digital oscilloscopes. Hantek HT25
zł133.54
24h
Available quantity: 7
Available
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 60 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-80
zł29.00
24h
Available quantity: 8
Available
Cable (adapter) of a BNC connector to banana plugs. Allows convenient connection of the device to an oscilloscope, for example. Hantek HT30A
zł35.46
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP600XS