Micsig RCP60XS - Rogowski AC current probe 60A
ID: 1197283
5902186321311
zł4,182.00
Tax included
zł3,400.00 tax excl.
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP60XS
Description
Micsig RCP is a Rogowski-type current probe designed for precise measurement of AC currents while maintaining a wide bandwidth up to 30 MHz. Thanks to its flexible, thin coil with a cross-section of only 1.6 mm, the device is perfect for hard-to-reach areas in electronic circuits, such as the leads of TO-220 transistors or other power semiconductors. The probe introduces almost zero input impedance, minimizing impact on the Device Under Test (DUT). An integrated amplifier powered by 12 V DC enables accurate measurement of highly dynamic, high-frequency signals.
The BNC interface allows for easy connection to any oscilloscope. The device offers a typical accuracy of 2% and excellent resistance to interference and high voltages up to 1 kVrms. The RCP probe is widely used in power electronics research—from switching current measurements in MOSFET and IGBT transistors to power quality analysis in inverters, UPS units, and SMPS systems. Its compact design and customizable coil parameters make it an invaluable tool for R&D labs and diagnostic departments.
Features
- Bandwidth: 85 Hz to 30 MHz
- Rise time: ≤ 11.6 ns
- Maximum current: 60 A (peak)
- Output sensitivity: 100 mV/A (10x mode)
- Typical accuracy: ±2%
- Output noise: < 20 mVpp
- Slew rate: 4 kA/μs
- Signal droop: 65%/ms
- Delay: 26.2 ns
- Conductor positioning effect: ±1%
- Offset voltage: < ±1 mV
- Coil insulation: 1 kVrms for 1 min
- Max measured conductor diameter: ≤ 20 mm
- Power supply: DC 12V
- Output impedance: 1 MΩ
- Interface: standard BNC
- CE standards: EN IEC 61010-2-032
- EMC standards: EN IEC 61326-1:2021 and others
- Operating temperature range: base 0°C–55°C, coil –20°C–125°C
- Storage temperature range: –30°C–70°C
- Operating humidity: ≤ 85% RH
- Storage humidity: ≤ 90% RH
- Integrator dimensions: 70 × 40 × 17 mm
- Cable length: 1.5 m (customizable)
- Inner coil diameter: 25 mm (customizable)
- Coil circumference: 80 mm (customizable)
- Coil cross-section: approx. 1.6 mm
1197283
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP12000XS
zł5,043.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP6000XS
zł4,551.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP3000XS
zł4,551.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP120XS
zł4,182.00
Delivery date unknown
No product available!
Other products in the same category (16)
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100
zł32.57
24h
Available quantity: 38
Available
Test probe tip with 1000X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 350 MHz and 500 MHz frequency bands. Micsig OP1000-5
Product available on request. Please send your inquiry to the following address: sales@kamami.com
zł4,598.99
Delivery date unknown
No product available!
Oscilloscope Probes (pair). 460-004
zł136.75
24h
Available quantity: 3
Available
A probe tip with attenuation factor of 100X. Dedicated to Micsig probes from the SigOFIT series operating in the 500 MHz frequency band. Micsig OP100-5
zł4,065.81
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP300XS
zł4,059.00
4 weeks
No product available!
Test probe tip with 10X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 100 MHz and 200 MHz frequency bands. Micsig OP10-2
Product available on request. Please send your inquiry to the following address: sales@kamami.com
zł2,600.76
Delivery date unknown
No product available!
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a 300 MHz frequency band and the ability to measure voltage up to 3000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP3003
zł4,059.00
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP6000XS
zł4,551.00
4 weeks
No product available!
A probe tip with attenuation factor of 200X. Dedicated to Micsig probes from the SigOFIT series operating in the frequency band of 100MHz, 200MHz and 350MHz. Micsig OP200-3
zł1,398.90
4 weeks
No product available!
Micsig DP series differential probe based on advanced SigOFIT technology. It offers a frequency band of 200 MHz and the ability to measure voltage up to 3000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP3002
zł1,902.91
4 weeks
No product available!
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT25COP
zł440.00
24h
Available quantity: 4
Available
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 200 MHz, it can be connected to the oscilloscope via the BNC connector. Micsig MOIP200P
zł18,018.44
4 weeks
No product available!
The Micsig P300 oscilloscope probe with a BNC connector offers a bandwidth of 300 MHz and a maximum input voltage of 600 V, enabling precise measurements of high-frequency and high-voltage signals. Its high input impedance minimizes impact on the circuit under test, ensuring measurement accuracy. The standard BNC connector ensures compatibility with most oscilloscopes, making it a versatile tool for laboratories and engineering applications.
zł201.82
24h
Available quantity: 2
Available
LCRkelvin is a four-wire Kelvin probe for precise measurement of RLC components with minimal wire resistance impact. Equipped with gold-plated Kelvin clips, it ensures accuracy and reliability, and its design is compatible with LCR meters from various brands, such as Hantek and Uni-T
zł141.61
24h
Available quantity: 3
Available
Insulated fiber optic probe with a measuring range up to 2500 V. It works in the band up to 100 MHz, it can be connected to the oscilloscope via the BNC connector. Comes with a 10X attenuation tip. MOIP100P
zł12,099.01
4 weeks
No product available!
Oscilloscope probe designed to analyze signals generated by the ignition coil in car engines. It is compatible with most digital oscilloscopes. Hantek HT20COP
zł237.49
24h
Available quantity: 4
Available
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP60XS