zł10,639.61
.png)
New products
New products New products
Micsig RCP12000XS - Rogowski AC 12000A Current Probe
ID: 1197279
5902186321274
zł5,043.00
Tax included
zł4,100.00 tax excl.
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP12000XS
Description
Micsig RCP is a Rogowski-type current probe designed for precise measurement of AC currents while maintaining a wide bandwidth up to 30 MHz. Thanks to its flexible, thin coil with a cross-section of only 1.6 mm, the device is perfect for hard-to-reach areas in electronic circuits, such as the leads of TO-220 transistors or other power semiconductors. The probe introduces almost zero input impedance, minimizing impact on the Device Under Test (DUT). An integrated amplifier powered by 12 V DC enables accurate measurement of highly dynamic, high-frequency signals.
The BNC interface allows for easy connection to any oscilloscope. The device offers a typical accuracy of 2% and excellent resistance to interference and high voltages up to 1 kVrms. The RCP probe is widely used in power electronics research—from switching current measurements in MOSFET and IGBT transistors to power quality analysis in inverters, UPS units, and SMPS systems. Its compact design and customizable coil parameters make it an invaluable tool for R&D labs and diagnostic departments.
Features
- Bandwidth: 2 Hz to 30 MHz
- Rise time: ≤ 11.6 ns
- Maximum current: 12000 A (peak)
- Output sensitivity: 0.5 mV/A (2000x mode)
- Typical accuracy: ±2%
- Output noise: < 6 mVpp
- Slew rate: 70 kA/μs
- Signal droop: 2%/ms
- Conductor positioning effect: ±1%
- Offset voltage: < ±1 mV
- Coil insulation: 1 kVrms for 1 min
- Max measured conductor diameter: ≤ 20 mm
- Power supply: DC 12V
- Output impedance: 1 MΩ
- Interface: standard BNC
- CE standards: EN IEC 61010-2-032
- EMC standards: EN IEC 61326-1:2021 and others
- Operating temperature range: base 0°C–55°C, coil –20°C–125°C
- Storage temperature range: –30°C–70°C
- Operating humidity: ≤ 85% RH
- Storage humidity: ≤ 90% RH
- Integrator dimensions: 70 × 40 × 17 mm
- Cable length: 1.5 m (customizable)
- Inner coil diameter: 25 mm (customizable)
- Coil circumference: 80 mm (customizable)
- Coil cross-section: approx. 1.6 mm
1197279
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP300XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP600XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP1200XS
zł4,059.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP3000XS
zł4,551.00
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP120XS
zł5,254.76
Delivery date unknown
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP60XS
zł4,182.00
Delivery date unknown
No product available!
Other products in the same category (16)
The Micsig DP series differential probe is based on advanced metal shielding technology. It offers a 100 MHz frequency bandwidth and the ability to measure voltages up to 7000 V. It uses the popular BNC connector and is powered by a USB Type-C connector. Micsig DP7000
zł4,807.54
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP12000XS
zł5,043.00
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP6000XS
zł5,145.95
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP3000XS
zł4,551.00
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP120XS
zł5,254.76
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is perfect for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP60XS
zł4,182.00
4 weeks
No product available!
The RIGOL PLA3204 analyzes logic signals with a maximum time resolution of 5 ns, ensuring high compatibility with various voltage standards. It is indispensable for diagnostics and testing of digital circuits using RIGOL MHO5000 and DHO5000 series oscilloscopes. RIGOL PLA3204
Regular pricezł767.40zł700.67
24h
Available quantity: 1
Available
Micsig MSP510 passive oscilloscope probe with a 500 MHz bandwidth and 1:10 attenuation designed for precise high-frequency signal measurements. Compatibility with the BNC standard and compensation adjustment make it a universal tool for laboratories and electronics workshops.
zł153.21
24h
Available quantity: 1
Available
The Micsig CP3008 probe is designed for precise measurement of AC/DC currents in high-voltage and high-current circuits. It is used in the analysis of switching power supplies, power converters, inverters, and testing of devices with high current loads.
zł10,421.79
4 weeks
No product available!
The Zeenko 3 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.
zł50.81
6 weeks
No product available!
The Zeenko 6 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.
zł58.67
6 weeks
No product available!
The Zeenko 20 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.
zł58.06
6 weeks
No product available!
The Zeenko 30 dB SMA attenuator is a solid and precise component for RF measurement paths, useful in diagnostics, calibration and protecting devices such as the tinySA, nanoVNA or RF generators. It enables safe measurements and improves impedance matching quality over a wide frequency range.
zł58.06
24h
Available quantity: 4
Available
The Zeenko N 10 dB attenuator is a reliable accessory for any RF system user – from amateurs to professionals. It enables safe and precise measurements and provides better signal matching in the signal path. Thanks to its high durability (up to 5 W), it is suitable for a wide range of laboratory and field applications.
zł71.93
24h
Available quantity: 11
Available
This current probe is designed for measuring DC and AC current in power electronics systems and switching power supplies. It offers a 10 MHz DC bandwidth, a rise time of ≤ 46 ns, and two measurement ranges: 30 A and 150 A RMS, with a maximum peak current of up to 300 A. The device provides high measurement accuracy of ±1% and a resolution of up to 10 mA in the lower range. The BNC connector ensures compatibility with many oscilloscopes, and the 20 mm jaws enable current measurements in larger wires. Micsig CP1510
zł6,696.40
4 weeks
No product available!
This current probe is designed for measuring DC and AC current in power electronics systems and switching power supplies. It offers a 5 MHz DC bandwidth, a rise time of ≤ 70 ns, and two measurement ranges: 50 A and 300 A RMS, with a maximum peak current of up to 500 A. The device provides high measurement accuracy of ±1% and a resolution of up to 10 mA in the lower range. The BNC connector ensures compatibility with many oscilloscopes, and the 20 mm jaws enable current measurements in larger wires. Micsig CP3005
zł6,603.87
4 weeks
No product available!
Rogowski-type current probe for precise measurements of alternating currents with a frequency of up to 30 MHz. Thanks to the flexible coil of 1.6 mm thickness and almost zero impedance introduced, it is ideal for work in hard-to-reach places of power systems. The integrated amplifier and BNC interface enable accurate measurements and easy integration with oscilloscopes, making it an ideal tool for R&D laboratories and power electronics services. Micsig RCP12000XS