The 50X attenuation probe tip is designed to extend the measurement range of Micsig high-frequency probes. It enables operation at high voltages, ensuring both safety and measurement accuracy. Its low input impedance minimizes impact on the measured signal. Fully compatible with OIP350 probes, this tip is ideal for signal analysis up to 100 MHz, 200 MHz, and 350 MHz in both laboratory and field environments. The compact design allows for easy access to hard-to-reach test points.
Manufacturer
Responsible person
Insulated fibre-optic probe with a measurement range of up to 2500 V. Operates up to 350 MHz and can be connected to an oscilloscope via a BNC connector. Battery-powered. Micsig OIP350B
No product available!
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000
A probe with a Rogowski coil dedicated to measuring current in a wide frequency range. Measurements can be made without modifying the circuit under test. Micsig RCP500
No product available!
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 60 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-80
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-150
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 200 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-200
High-voltage oscilloscope probe with BNC connector and 100:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 2 kV. Hantek T3100
A probe for measuring AC and DC currents up to 65 A. It operates in a bandwidth of up to 20 kHz and can be connected to an oscilloscope via a BNC connector. Hantek CC-65
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650
No product available!
The housing for the DSO138 oscilloscope allows for easy storage and mobile use of the device. It protects the PCB and any microcircuits on it from dirt or accidental damage.
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100
Oscilloscope probe designed for the analysis of signals generated by the ignition coil in automotive engines. It is compatible with most digital oscilloscopes. Hantek HT25
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.8mm
No product available!
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-2.3mm
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.5mm
6-wire test leads that allow the oscilloscope to be connected to various components in the engine compartment without stripping or puncturing the insulation and without risking damage to the connectors. Hantek HT306-1.0mm
The probe tip has a 50X attenuation factor. Designed for Micsig probes from the SigOFIT series operating in the 100MHz, 200MHz and 350MHz frequency band. Micsig OP50-3