A probe for measuring DC and AC currents up to 650 A. It uses a standard BNC interface and can be connected to an oscilloscope or multimeter. It operates in the frequency band up to 400 Hz. The jaw spacing allows measurement of current flowing in wires with a maximum diameter of 30 mm. It will find use in industry, automotive electronics, power supplies and inverters.
Manufacturer
Responsible person
A multifunctional device (computer attachment) that combines a 2-channel digital oscilloscope and a 16-channel logic analyzer. Hantek6022BL
Digital oscilloscope. It has two measurement channels with 100 MHz bandwidth. Hantek DSO2C10
Digital oscilloscope. It has two measurement channels with 150 MHz bandwidth. Hantek DSO2C15
Digital oscilloscope with built-in signal generator. It has two measurement channels with 100 MHz bandwidth and a single-channel signal generator with waveform frequencies up to 25 MHz. Hantek DSO2D10
Probe for measuring direct and alternating current up to 100 A. It works in the 2,5 MHz band, it can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP2100B
Universal oscilloscope probe with BNC plug with 100: 1 voltage divider and 100 MHz bandwidth. It allows you to perform measurements with a maximum voltage of 2 kV
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 100 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP1003B
No product available!
Probe for measuring direct and alternating current up to 30 A. Works in the band up to 50 MHz, can be connected to the oscilloscope through the BNC connector. Powered by USB. Micsig CP503B
No product available!
Probe for measuring AC currents up to 1000 A. It works in the range from 10 Hz to 100 kHz, it can be connected to the oscilloscope through the BNC connector. Micsig ACP1000
A probe with a Rogowski coil dedicated to measuring current in a wide frequency range. Measurements can be made without modifying the circuit under test. Micsig RCP500
No product available!
A 20:1 signal attenuator designed to assist in measuring automotive performance, including measuring fuel injector and primary ignition runs. Hantek HT201
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 60 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-80
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-150
A universal oscilloscope probe with a BNC connector and a 10:1 voltage divider. It has a frequency response of 200 MHz and allows measurements with a maximum voltage of up to 600 V. Hantek PP-200
High-voltage oscilloscope probe with BNC connector and 100:1 voltage divider. It has a frequency response of 100 MHz and allows measurements with a maximum voltage of up to 2 kV. Hantek T3100
A probe for measuring AC and DC currents up to 65 A. It operates in a bandwidth of up to 20 kHz and can be connected to an oscilloscope via a BNC connector. Hantek CC-65
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650
No product available!
The housing for the DSO138 oscilloscope allows for easy storage and mobile use of the device. It protects the PCB and any microcircuits on it from dirt or accidental damage.
Universal oscilloscope probe with BNC connector. It has a voltage divider of 10:1 and offers a frequency response of 100 MHz. It allows measurements with a maximum voltage of up to 600 V. P6100
Oscilloscope probe designed for the analysis of signals generated by the ignition coil in automotive engines. It is compatible with most digital oscilloscopes. Hantek HT25
A probe for measuring AC and DC currents up to 650 A. It operates in a bandwidth of up to 400 Hz and can be connected to an oscilloscope via a BNC connector. Hantek CC-650