MyoWare Power Shield
ID: 561543
zł24.33
Tax included
zł19.78 tax excl.
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. Connecting the MyoWare Muscle Sensor to battery power allows for a cleaner signal while also eliminating the possibility of creating a dangerous current path to the power grid.
One thing to note is that due to the size of the batteries, the remote cable header on the MyoWare Miscle Sensor can’t be passed through. If you need access to these connections, this Power Shield will need to be stacked above the board(s) that need access.
The MyoWare Muscle Sensor, that this shield attaches to, is an Arduino-powered, all-in-one electromyography (EMG) sensor from Advancer Technologies. The MyoWare board acts by measuring the filtered and rectified electrical activity of a muscle; outputting 0-Vs Volts depending the amount of activity in the selected muscle, where Vs signifies the voltage of the power source.
Note!
The MyoWare Power Shield and the MyoWare LED Shield both provide power, but at slightly different voltages. Don’t use both of these shields at the same time.
561543
You might also like
Available
Other products in the same category (16)
The module with the MAX30100 chip that monitors the oxygen content in the blood and the heart rate. It consists of two LED diodes, a photodetector, optimized optics and low noise analog signal processing. modMAX30100
zł14.90
24h
Available quantity: 14
Available
Module with GSR skin resistance sensor. It is used to measure skin activity, which reflects the stress response and experienced emotions. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020052
zł51.38
24h
Available quantity: 4
Available
A module with a sensor used to measure the activity of the heart. It allows you to strengthen and extract the heartbeat signals from biomedical electrodes. It has an analogue output and a heartbeat indicator (LED). SparkFun SEN-12650
zł94.70
24h
Available quantity: 4
Available
Available
The sensor responds to chakra changes in the tissues by analyzing the reflected light (the module contains an illuminator and a sensor).
zł14.90
24h
Available quantity: 5
Available
Module with pulse and SpO2 level sensor (oxygen saturation level). The module is based on the MAX30102 chip and communicates via the I2C interface.
zł11.03
6 weeks
No product available!
Evaluation board with built-in AD8232 heart monitor module and components placed in a way allowing effective implementation of medical and fitness applications, configuration of 2 or 3 electrodes
zł289.00
6 weeks
No product available!
Module with heart rate and SpO2 sensor (oxygen saturation level) MAX30100 designed for M5Stack sets. M5Stack U029
zł54.00
24h
Available quantity: 3
Available
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
zł38.90
24h
Available quantity: 2
Available
A module with an EMG sensor that detects the activity of human muscles and neurons. Generates an analog signal in the range from 0 to 3 V on the output, it does not require the use of a conductive gel. DFRobot SEN0240
zł261.94
24h
Available quantity: 3
Available
Module with heart rate sensor, SpO2 (oxygen saturation) and smoke levels. It is based on the MAX30101 chip and communicates via the I2C interface. Pimoroni PIM438
zł99.73
24h
Available quantity: 4
Available
Sensor module for electromyography (EMG). Allows muscle activity to be studied and used to control devices. SparkFun DEV-21265
zł219.00
6 weeks
No product available!
Available
Module with an EMG signal detector. The board is equipped with a Grove connector and has an analog output. Seeed Studio 101020058
zł160.67
6 weeks
No product available!
Designed to pair with the MyoWare Muscle Sensor; 10-segment bar graph shows the magnitude of the measured signal. The more muscle activation measured, the higher up the board the lit LEDs will go. DEV-13688
zł120.98
24h
Available quantity: 6
Available
Module with a sensor for measuring the heart rate PAH8001EI-2G. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020082
zł158.45
6 weeks
No product available!
The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board in a way that the coin cell batteries are connected in parallel for extended capacity at a nominal 3.0V. DEV-13684