

Small, metal gear motor with M3 threaded shaft, approx. 55 mm long. The recommended operating voltage of the motor is 6 V and at this voltage it achieves a speed of 200 RPM and a maximum torque of 0,7 kg * cm, consuming a current from 0.055 A to 0.58 A.
The recommended supply voltage for the motors is 6 V, but the motors operate without problems in the range from 3 V to 9 V. It is possible to supply the motor with higher voltage, but it reduces the service life of the motor.
All N20M engines have the same dimensions. The metal gear housing has two tapped holes for M1.6 bolts (1.6mm diameter, 0.35mm pitch). The engines weigh approx. 15 g.
![]() |
Dimensions of N20M micromotors (units in mm). |
---|
Our offer includes N20M engines with gear ratios from 50: 1 to 200: 1.
Gear ratio | Version | Voltage | Rotation speed | max. torque | min. current | max. current | Link |
50:1 | MP | 6 V | 300 RPM | 0,4 kg*cm | 55 mA | 0,58 A | LINK |
100:1 | MP | 6 V | 200 RPM | 0,7 kg*cm | 55 mA | 0,58 A | LINK |
150:1 | MP | 6 V | 100 RPM | 1,1 kg*cm | 55 mA | 0,58 A | LINK |
200:1 | MP | 6 V | 60 RPM | 1,4 kg*cm | 55 mA | 0,58 A | LINK |
250:1 | MP | 6 V | 50 RPM | 1,8 kg*cm | 55 mA | 0,58 A | LINK |
298:1 | MP | 6 V | 30 RPM | 2,1 kg*cm | 55 mA | 0,58 A | LINK |
It is not possible to control the motors directly from the microcontroller ports due to the high power consumption. This problem is solved by the motor drivers. Thanks to the controllers, it is possible not only to turn on and only the motors, but also to control their speed and direction of rotation.
Our offer includes a number of drivers for one or two motors. The drivers are available in the form of modules, shield extensions for Arduino and hat extensions for Raspberry Pi.
![]() |
![]() |
![]() |
DC motor controller with DRV8838 Pololu system | Shield Arduino with dual driver for DC motors with A4990 chip | Dual driver for DC motors with the DRV8835 chip |
Current sensors measure how much current the motors are consuming at a given moment, which allows to determine the load on the motors. Our offer includes sensors with measuring ranges from ± 5 to ± 75.
![]() |
![]() |
![]() |
Current sensor module 0-5A with ACS712-05 chip | Current sensor module ± 5A with ACS714 chip | Current sensor module ± 15.5A with ACS711EX system |
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
N20 MP 3V 300RPM is a compact motor with a 50:1 gearbox, designed for use in lightweight mobile constructions. It offers a balance between torque and speed with very low power consumption and easy mounting.
Small metal gear motor, 15 RPM speed, 3V operating voltage. GA12-N20-0001
Small metal gear motor, 100 RPM speed, 3V operating voltage. GA12-N20-0005
A small, low-power motor with a 5:1 metal gear, 6 V operating voltage, 0.02 A to 0.36 A power consumption, 2500 RPM speed and a maximum torque of 0.05 kg * cm. Pololu 1100
A small, high power motor with 380: 1 metal gear, 6 V operating voltage, 0.07 A to 1.6 A power consumption, 84 RPM and a maximum torque of 5.5 kg * cm. Pololu 4794
No product available!
This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 297.92:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
No product available!
Miniature, 12 V brush DC motor with metal gear and 15.25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft with a length of 9 mm and a diameter of 3 mm. Pololu 4788
No product available!
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 100 RPM, operating voltage 6 V. GA1036-N20M-0055
This gearmotor is a miniature high-power, 12 V brushed DC motor with long-life carbon brushes and a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
Key specs at 12 V: 320 RPM and 100 mA with no load, 30 oz-in (2.2 kg-cm) and 0.8 A at stall.
Pololu high power miniature motor with carbon brushes. 210:1 gear motor, shaft speed 85 rpm, torque 2.5kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 3054
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 4.995:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
298:1 Micro Metal Gearmotor
A small medium power motor with 210:1 metal gear, 6 V operating voltage, 0.04 A to 0.67 A power consumption, 100 RPM speed and a maximum torque of 1.7 kg*cm. Pololu 2369
No product available!
100:1 Micro Metal Gearmotor with Extended Motor Shaft
298:1 Micro Metal Gearmotor MP
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 200 RPM, operating voltage 6 V. GA1036-N20M-0056