- New
New products
New products New products
zł59.96
24h
Available
Available
2-Channel Relay Module with Optoisolation-10A/250VAC Contacts, 5V Coil
ID: 1202349
zł9.90
Tax included
zł8.05 tax excl.
Two-channel relay module equipped with optoisolated control inputs and relays with 5V coils. Designed for controlling loads up to 10A at 250VAC from a microcontroller or development platforms
Description
The relay module is designed for controlling actuators using digital signals generated by microcontrollers and development platforms. The solution enables safe switching of loads powered by AC mains or DC voltage, such as lighting, motors, solenoid valves, and other electrical devices that require isolation from the logic control section.
The board is equipped with two electromagnetic relays with 5V coils, whose contacts allow switching currents up to 10A at 250VAC or 110VDC. Optoisolated control inputs separate the logic signals from the relay circuits, reducing interference and increasing the operational safety of the microcontroller.
Connection outputs
The module supports control signals with logic levels of 3.3V and 5V. The relays are activated by a low logic level. A jumper between the VCC and JD-VCC lines allows independent power supply of the logic section and the relay coils. Standard 2.54mm pitch pin headers and ARK screw terminals facilitate integration with installations and mounting in prototyping and educational projects.
Features
- Number of channels: 2
- Relay coil voltage: 5 V
- Logic supply voltage: 3.3 – 5 V
- Control method: active-low
- Maximum contact voltage: 250 VAC, 110 VDC
- Maximum contact current: 10 A
- Optoisolated control inputs
- Control connectors: 2.54 mm pin headers
- Load connectors: ARK screw terminals
- Operating temperature: -40°C ~ 85°C
1202349
Data sheet
- Output current
- 10A
- Number of channels
- 2
- Executive element
- Przekaźnik elektromagnetyczny
- Coil voltage
- 5 VDC
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A set consisting of the most commonly used goldpin connectors
zł4.85
Delivery date unknown
No product available!
Other products in the same category (16)
Industrial module with Ethernet interface that allows control of 8 relays via RJ45 port and has 8 built-in digital inputs. It uses Modbus TCP protocol, PoE (Power over Ethernet) power supply and is equipped with a rail-mounted housing. Waveshare Modbus POE ETH Relay (B)
zł178.25
24h
Available quantity: 57
Available
Industrial relay module controlled via RS485 interface with Modbus RTU protocol support, offering 8 outputs with maximum load of 10 A. Equipped with galvanic isolation, opto-isolation, TVS diodes and DIN mounting, it ensures safe and reliable operation in harsh industrial conditions. Thanks to functions such as flash-on/off, configurable RS485 address (1-255), signaling diodes and wide power supply range (7-36 V), the module is perfect for building automation and device control. Waveshare Modbus RTU Relay (B)
zł139.67
4 weeks
No product available!
Module with a 12 V relay and a timer. It allows you to turn the device on and off cyclically at a specified time using potentiometers. It can also operate in single trigger mode, which allows the device to be turned on after a signal has been applied for a specified period of time. The operating time can be adjusted from 1 s to 100 s or from 1 s to 15 min
zł14.55
24h
Available quantity: 1
Available
Relay module for the WeMos D1 Mini WiFi set
zł5.41
24h
Available quantity: 10
Available
4-channel module with relays, designed to work with the Raspberry Pi. It can switch 120VAC/2A or 24VDC/2A signals. SB Components 14071
zł90.28
24h
Available quantity: 2
Available
Module with 4 relays with a maximum switching current of 7 A. Equipped with the ATmega328P microcontroller, it can be programmed in the Arduino IDE. Numato Lab PRLY002
zł437.79
24h
Available quantity: 1
Available
Module with 2 relays SRD-05VDC-SL-C with a load up to 10 A. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 103020132
zł46.59
24h
Available quantity: 2
Available
No product available!
Module with 2 SSR relays with a load of up to 3 A. The board is equipped with the ULN2003 system and communicates via a digital interface. Numato Lab SSRC20001-DC
zł323.98
24h
Available quantity: 1
Available
Numato Lab RL20001EN is a 2-channel USB relay module with SPDT relays, 8 GPIO pins, 6 analog inputs and a USB interface, ideal for home automation, industrial, DIY and prototyping applications
zł84.12
3 weeks
No product available!
Numato Lab\'s 1-Channel USB Relay Module is an easy-to-use, flexible and versatile device, ideal for remote control of devices, home automation, prototyping and DIY projects, offering a 5V DPDT relay, GPIO, analog inputs and compatibility with multiple operating systems and serial console applications
zł84.12
3 weeks
No product available!
Module with 4 5 V relays with a maximum switching current of 2 A. It communicates via the USB interface and does not require an additional power supply. Enclosure included. Numato Lab USBPOWRL004E
zł343.26
3 weeks
No product available!
Module with relay HF152FD 16A. It allows you to control devices with a current consumption of up to 16A using a low-power signal. The module has a relay activation time of about 10ms. DFRobot DFR0251
zł47.32
4 weeks
No product available!
Module with SSR relay with a load of up to 3 A. It communicates via the USB interface and does not require additional power supply. Numato Lab SSRP20001-AC
zł294.93
24h
Available quantity: 1
Available
Module with a relay and WiFi communication. Compatible with ESP-01 or ESP-01S
zł9.63
24h
Available quantity: 1
Available
Module with 2 relays 12 V with a maximum switching current of 7 A. Numato Lab RL20002
zł90.84
24h
Available quantity: 2
Available
Two-channel relay module equipped with optoisolated control inputs and relays with 5V coils. Designed for controlling loads up to 10A at 250VAC from a microcontroller or development platforms