Motoron M3S550 Triple Motor Controller Shield - 3-channel DC motor controller for Arduino (for assembly)
ID: 1185706
zł132.34
Tax included
zł107.59 tax excl.
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069
Description
DC motor driver dedicated to Arduino boards. It allows you to control the movement of three drives using the I2C interface. It can work with motors with a supply voltage from 1.8 to 22 V and has a capacity of up to 1.7 A per motor (continuous operation). The controller has a built-in protection in the event of loss of communication with Arduino and the ability to configure the response if an error occurs. The user can set the maximum acceleration and the starting speed of the motor, and the shield construction allows you to connect the drivers with each other. The manufacturer's website includes a user manual and a library with sample programs.
Features
- Operating voltage range: 1.8 V to 22 V
- Maximum output current per motor: 1.7 A continuous, 5 A instantaneous
- Voltage range of the logic part: 2.8 V to 5.5 V
- Control interface: I2C
- I2C clock frequency: up to 400 kHz
- CRC control capability
- Configurable motion parameters:
- Maximum acceleration/deceleration
- Initial speed
- Delay for change of direction
- PWM frequency: eight options available from 1 kHz to 80 kHz
- Protection in case of communication loss
- Configurable automatic error response
- Measurement of motor supply voltage (VIN)
- Possibility to power the Arduino directly or via an external stabiliser (not supplied)
- Two status LEDs
- Motor direction LEDs
Kit contains
- Motoron M3S550 Triple Motor Controller Shield
- Connector 1x10 straight female
- Connector 1x8 straight female
- 4 x 2pin 3.5 mm screw connector
- 4 x 2pin 5 mm screw connector
- Connector 1x25 straight male
1185706
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
24h
Available quantity: 105
Available
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
Regular pricezł207.92zł188.92
24h
Available quantity: 52
Available
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board without connectors is included. Pololu 5070
zł106.27
24h
Available quantity: 2
Available
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069
zł132.34
24h
Available quantity: 2
Available
Other products in the same category (16)
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
zł288.26
24h
Available quantity: 1
Available
Shield with DC motor driver for Arduino. It has an operating voltage of 7 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MD10
zł67.35
24h
Available quantity: 4
Available
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board without connectors is included. Pololu 5070
zł106.27
24h
Available quantity: 2
Available
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
zł115.42
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5047
zł406.69
4 weeks
No product available!
(DRI0009) 2A Motor Shield For Arduino
zł91.24
24h
Available quantity: 3
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for self-assembly. Pololu 5046
zł435.53
4 weeks
No product available!
Pololu Dual G2 High-Power Motor Driver 24v18 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 40V voltage and can draw a maximum current of 18A. Pololu 2518
zł420.17
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5039
zł352.15
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5045
zł456.85
4 weeks
No product available!
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 1.2 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-3AMOTOR
zł111.29
24h
Available quantity: 2
Available
Expansion board for three stepper motor drivers compatible with Arduino Nano. The stepper driver connectors fit A4988 modules
zł15.01
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5036
zł352.15
4 weeks
No product available!
DC motor driver that allows you to control the movement of three drives using the I2C interface. The set includes only the board without connectors. Pololu 5032
zł177.08
4 weeks
No product available!
Pololu 2512Module with 2-channel DC motor driver for Arduino boards. It allows you to control drives with a supply voltage from 6 to 32 V and a current consumption of up to 0.65 A. Pololu 2512
zł66.92
24h
Available quantity: 3
Available
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its dual robust VNH5019 motor drivers operate from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak) per motor, or a continuous 24 A (60 A peak) to a single motor connected to both channels. Pololu 2507
zł294.77
4 weeks
No product available!
DC motor controller that allows the movement of three drives to be controlled via an I2C interface. A board with connectors for mounting is included. Pololu 5069