

zł42.98 tax excl.
Uninterruptible power supply module for Raspberry Pi Pico, which allows you to continue work and safely shut down the microcomputer after a power failure. Waveshare Pico-UPS-A-EN
Uninterruptible power supply module designed for Raspberry Pi Pico. After connecting the 14500 type battery, the power supply maintains a stable output voltage of 5 V even after a power loss, which allows the device to continue operating and safely shut down. The battery charge status is indicated by built-in LEDs, and full battery status monitoring is possible thanks to the I2C interface. The board has a battery charging circuit and protection against overcharging and discharging, overcurrent, short-circuit and reverse polarity protection. It is connected to the Raspberry Pi Pico via a dedicated connector. The manufacturer has prepared numerous examples in C/C++ and MicroPython for the set. Full documentation is available on the product Wiki page.
Attention!
The kit does not include 14500 and Raspberry Pi Pico batteries. They must be purchased separately.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Raspberry Pi Pico
Li-Ion 14500 battery with a nominal voltage of 3.7 V and a capacity of 800 mAh. It has overcharge, over discharge, overload and short circuit protection. XTAR ACCU-14500-0.8-2A
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Version with soldered connectors. Raspberry Pi SC0917
Keyboard module designed for Raspberry Pi Pico. It is equipped with 16 buttons with RGB backlight. Pimoroni PIM551
No product available!
Monochrome VGA camera module with HM0360 sensor working with Raspberry Pi Pico. It uses 1 bit video interface and I2C to configure the registers. ArduCAM B0319
The PMSA003 air quality sensor module to work with the Raspberry Pi Pico. It allows for a analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. SB Components 21819
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
Uninterruptible power supply module for Raspberry Pi Pico, allowing you to continue working and safely shut down after a power failure. Waveshare Pico-UPS-B
Board with prototype holes dedicated to Raspberry Pi Pico. It offers an 8x20 hole area with a pitch of 2.54 mm with marked pin labels and a reset button and STEMMA QT connector. Adafruit 5200
Expansion module with audio and video outputs dedicated to Raspberry Pi Pico boards. It has a VGA output, SD card slot, audio outputs and control buttons. Pimoroni PIM553
The Raspberry Pi Debug Probe is an affordable tool that combines a USB-UART debugger and converter. Includes the necessary hardware and wiring needed to quickly debug the Raspberry Pi Pico, RP2040 microcontrollers, and other ARM Cortex-based MCUs. Raspberry Pi SC0889
Mini HDMI module for Raspberry Pi Pico. It allows you to send a video signal, e.g. to a monitor or TV. It is equipped with a STEMMA QT connector. Adafruit 5745
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 120 V AC or 24 V DC and currents up to 2 A. SB Components 21376
Module with 4-digit 8-segment LED display. Communication via the SPI interface. Waveshare Pico-8SEG-LED
The module with screw connectors is dedicated to the Raspberry Pi Pico boards. It allows you to easily create prototypes, ensuring a stable connection of wires with the board. DFRobot DFR0924
The KamodRPI Pico Quad SSR is an add-on board for Raspberry Pi Pico featuring four solid-state relays (SSR), optoisolated digital inputs, and LEDs indicating input and output states. The module is ideal for building automation, robotics, and education, with automatic power source selection between micro USB and USB-C
Audio module with speakers designed to work with the Raspberry Pi Pico. Waveshare Pico-Audio
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21284
A set of goldpin male connectors intended for Raspberry Pi Pico boards. The set includes two 20-pin strips and one 3-pin strip with a pitch of 2.54 mm. Soldered connectors enable easy connection of expansion modules and other accessories
Uninterruptible power supply module for Raspberry Pi Pico, which allows you to continue work and safely shut down the microcomputer after a power failure. Waveshare Pico-UPS-A-EN