- Out-of-Stock
MyoWare 2.0 Muscle Sensor - a module with a muscle tension sensor
ID: 1178921
Electromyography (EMG) sensor module. It allows you to study muscle activity and use it to control devices. SparkFun DEV-18977
Description
MyoWare 2.0 Muscle Sensor is a module with a muscle tension sensor, a universal electromyography (EMG) sensor from Advancer Technologies. It is easy to use, and with its compact design and dedicated layout, it offers good performance and reliability. The snap-in connector system eliminates the need to solder the connections, allowing the user to easily connect the sensor to the development board.
The sensor measures muscle activity by measuring the electrical potential of the muscles, commonly referred to as surface electromyography (EMG or sEMG for short). The system analyzes electrical activity and sends an analog signal (0-VIN, where VIN is the voltage of the power source) that shows how much the muscle is tightened. MyoWare 2.0 offers three types of output: Raw EMG (raw data), Rectified (rectified signal) and Envelope (linear signal).
The MyoWare 2.0 Muscle Sensor tile is powered with the voltage from 3.3 V to 5 V, has a reverse polarity protection and LED indicators. The module connects to other expansion boards from the MyoWare 2.0 series using snap pins.
The MyoWare 2.0 system allows you to build devices for the medical analysis of muscle tension, as well as controllers used in the areas of robotics and video games. Modules are prototypical elements and therefore are not intended for diagnosis or treatment. Full documentation and numerous examples of use are available on the product page.
Features
- Output Modes: Raw EMG, Rectified, Envelope
- Snap Connectors:
- 3 x female (power supply, Envelope EMG output)
- 3 x male (electrode input)
- Adjustable gain
- Reverse current protection
- LED indicators: VIN, ENV
- Power supply: 2.27 V to 5.47 V
- Input bias current: 250 pA, max 1 nA
- Dimensions: 37.57 x 35.9 mm
1178921
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
Cable dedicated to MyoWare 2.0 muscle tension sensors. It allows you to connect the electrode with the plate in the event that it must be located at a distance from the sensor. SparkFun CAB-19244
zł7.00
Delivery date unknown
No product available!
Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18386
zł29.34
24h
Available quantity: 1
Available
Module with 3.5 mm TRS connector for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect the sensors with the development board via the Arduino shield. SparkFun DEV-18425
zł67.24
Delivery date unknown
No product available!
Arduino Shield with connectors for MyoWare 2.0 muscle tension sensors. It allows you to conveniently connect sensors with the development board. SparkFun DEV-18426
zł58.50
Delivery date unknown
No product available!
The power module is designed for the MyoWare 2.0 muscle tension sensor. Equipped with a LiPo battery, it allows you to build portable devices. SparkFun DEV-18427
zł102.20
24h
Available quantity: 1
Available
Other products in the same category (16)
Ribbon Cable, IDC Socket, IDC Socket, 40 Ways, 5.91 ", 150 mm, 2.54 mm
Retired
No product available!
No product available!
No product available!
FRAM memory with a capacity of 4kbit by Cypress Semiconductor, communicates via the I2C bus, the power supply voltage is in the range 2.7 - 3.6V. The system has an SOIC8 housing
Retired
No product available!
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
Retired
No product available!
Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm
Delivery date unknown
No product available!
KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO
Retired
No product available!
K64 microcontroller with ARM® Cortex®-M4 core, 1MB Flash memory, 256kB RAM, 120MHz, SPI, I2C, I2S, UART, CAN, USB OTG, ADC, DAC, RTC, DMA, LQFP100
Retired
No product available!
SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902
Retired
No product available!
Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors: 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope. Adafruit 2020
Retired
No product available!
Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981
Retired
No product available!
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
Retired
No product available!
FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229
Retired
No product available!
32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon
Retired
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
Retired
No product available!
Electromyography (EMG) sensor module. It allows you to study muscle activity and use it to control devices. SparkFun DEV-18977