- Out-of-Stock
Li-Po Battery Akyga LP603048 3.7V 850mAh PCM JST 2.54
ID: 1202742
5906574243445
Lithium-polymer Li-Po battery with a nominal voltage of 3.7V and a capacity of 850mAh, equipped with a PCM protection circuit and a lead with a JST 2.54 2-pin connector, 150mm long. Akyga AKY0108
Description
Akyga AKY0108 is intended for powering electronic devices operating at a nominal voltage of 3.7V. The LP603048 cell format provides a capacity of 850mAh and a flat construction, enabling installation in enclosures with limited internal space, such as portable electronics, control modules, and embedded projects.
The integrated PCM protection circuit supervises charging and discharging processes, reducing the risk of damage caused by overcharging, deep discharge, short circuit, and overcurrent. The battery is connected via a 150mm lead terminated with a 2-pin JST 2.54 connector, allowing direct connection to development boards, power supply modules, and charging controllers. The AKY0108 model is used in consumer electronics, IoT systems, robotics, and electronic projects requiring compact Li-Po power sources.
Warning!
Before installation, read and follow the safety guidelines for lithium-polymer batteries. Improper use may result in damage to the battery!Features
- Battery type: lithium-polymer Li-Po
- Cell format: LP603048
- Nominal voltage: 3.7V
- Nominal capacity: 850mAh
- Configuration: 1S
- Number of cells: 1
- Protection circuit: PCM
- Rechargeable: yes
- Connector: JST 2.54 2-pin
- Cable length: 150mm
- Lead type: wires
- Application: powering electronic devices operating at 3.7V
Kit includes
- 1x Lithium-polymer Li-Po battery with cable and JST 2.54 2-pin connector
1202742
Data sheet
- Battery type
- Li-Po
Other - Output voltage
- 3.7V
- Battery capacity
- 850mAh
- Battery configuration
- 1S
- Number of cells
- 1
- Output/Connector
- JST 2,54 mm
- Length
- 48mm
- Width
- 30mm
- Thickness
- 6mm
- Weight
- 19 g
Manufacturer AKYGA EUROPE SPÓŁKA Z OGRANICZONĄ ODPOWIEDZIALNOŚCIĄ Wrocławska 1C 52-200 Suchy Dwór Poland contact@akyga.com
Responsible person AKYGA EUROPE SPÓŁKA Z OGRANICZONĄ ODPOWIEDZIALNOŚCIĄ Wrocławska 1C 52-200 Suchy Dwór Poland contact@akyga.com
Other products in the same category (16)
Video splitter for connecting one input device to 8 receivers. Maximum 4K resolution supported. Lanberg SPV-HDMI-0008
Retired
No product available!
Video switch that allows you to connect 5 input devices to one HDMI receiver. The input signal can be selected using a button on the casing or the included remote control. Lanberg SWV-HDMI-0005
Retired
No product available!
A set of 8 knives, including 4 knives with broken blades and 4 special-purpose knives. Vorel 76280
Retired
No product available!
Module with an analog temperature and humidity sensor based on the SHT10 system. It is characterized by high reliability and stability with low energy consumption. It is compatible with 3.3V and 5V controllers. DFRobot DFR0066
Retired
No product available!
Module with a CCS811 air quality sensor for measuring the concentration of carbon dioxide (eCO2) and volatile organic compounds (TVOC) in the air. It communicates via the I2C interface (Gravity connector). DFRobot SEN0318
Retired
No product available!
Module with a gesture and touch sensor. It recognizes 7 types of gestures and has 5 touch buttons. It is supplied with a voltage ranging from 3.3 V to 5 V and communicates via UART. DFRobot SEN0285
Retired
No product available!
Module with a 3-axis analog MMA7361 accelerometer. There are 3 Gravity connectors on the board (for each axis). The operating range of the sensor can be configured using a DIP switch. DFRobot DFR0143
Retired
No product available!
Module with a UV ultraviolet light sensor VEML6075. Enables measurement of the level of UVA (350-375 nm) and UVB (315-340 nm) radiation. It communicates via the I2C bus. DFRobot SEN0303
Retired
No product available!
The I2C-GPIO converter module is powered with the voltage of 5 V. It allows you to extend the number of digital pins of the Arduino-compatible board with an additional 16 IO pins. DFRobot DFR0013
Retired
No product available!
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with an RF wireless communication module operating at 433 MHz. Sonoff DW2 - RF
Retired
No product available!
Opening/closing sensor designed for mounting on windows and doors. It is equipped with a WiFi wireless communication module. Sonoff DW2
Retired
No product available!
Universal WiFi controlled switch. It can control one home appliance. Sonoff Basic R2 v2.2
Retired
No product available!
Wireless temperature and humidity sensor. It allows you to track changes in temperature and humidity in your home. Shelly H&T
Retired
No product available!
Power adapter with a microUSB socket designed for the Shelly H&T sensor. It allows you to replace the battery power of the sensor with a constant 5V power supply. Shelly H&T Usb Adapter
Retired
No product available!
Device for activating scenes and actions with WiFi communication. It can handle 3 connected input devices and show their status and control other connected Shelly relays, sensors or devices controlled by HTTP, MQTT or CoAP. Shelly i3
Retired
No product available!
Lithium-polymer Li-Po battery with a nominal voltage of 3.7V and a capacity of 850mAh, equipped with a PCM protection circuit and a lead with a JST 2.54 2-pin connector, 150mm long. Akyga AKY0108