- Out-of-Stock
ST-LINK
ID: 138463
ST-LINK in-circuit debugger / programmer for ST microcontrollers
ST-LINK in-circuit debugger / programmer for ST microcontrollers
ST-LINK is a very low-cost, in-circuit debugger / programmer for the STM8 and STM32. It connects to the application for the STM and the JTAG standard connection for STM32 microcontrollers.
For the STM8 MCUs, ST-LINK is driven by ST toolset, ST Visual Develop -STVD (version 4.1.0 or later) for in-circuit debugging and ST Visual Program -STVP (version 3.1.0 or later) for in-circuit programming and IAR toolset EWSTM8 (version 1.10 or later).
For STM32 MCUs, ST-LINK is driven by the Atollic toolset, TrueSTUDIO (version 1.0 or later), IAR toolset EWARM (version 5.30 or later) and Keil toolset ARM-MDK (version 3.3 or later).
Attention! Please visit the website www.stm32.eu , where you can find designs and advice for users of STM32 microcontrollers.
 | A newer version of the interface is available - ST-Link / V2 |
ST-LINK is a very low-cost, in-circuit debugger / programmer for the STM8 and STM32. It connects to the application for the STM and the JTAG standard connection for STM32 microcontrollers.
For the STM8 MCUs, ST-LINK is driven by ST toolset, ST Visual Develop -STVD (version 4.1.0 or later) for in-circuit debugging and ST Visual Program -STVP (version 3.1.0 or later) for in-circuit programming and IAR toolset EWSTM8 (version 1.10 or later).
For STM32 MCUs, ST-LINK is driven by the Atollic toolset, TrueSTUDIO (version 1.0 or later), IAR toolset EWARM (version 5.30 or later) and Keil toolset ARM-MDK (version 3.3 or later).
Features
- 5 V power supplied by USB connector
- USB 2.0 full speed interface compatible
- USB standard A to Mini-B cable provided
- STM8 SWIM specific features
- 1.65 V to 5.5 V application voltage supported
- SWIM low-speed and high-speed modes supported
- The ERNI standard vertical or horizontal connector
- SWIM cable for connecting to pin headers or 2.54 mm pitch connector
- STM32 JTAG specific features
- 3 V to 3.6 V application voltage supported on JTAG interface and 5 V tolerant inputs
- JTAG 20 pin 2.54 mm pitch connector
Contents
- ST-LINK debugger / programmer
- USB type A to Mini-B cable
- JTAG / SWD flat ribbon
- SWIM separate-wires cable
- SWIM flat ribbon with standard ERNI connector
138463
You might also like
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
zł123.81
24h
Available quantity: 24
Available
Other products in the same category (16)
Real-time clock with PCF8563 chip and battery backup. Modally MOD-48.Z
Retired
No product available!
V4 features the same sensors as v3 (L3GD20H, LSM303D) and adds an LPS25H digital barometer. An I²C interface accesses 10 independent measurements that can be used to calculate the sensor’s altitude and absolute orientation.
Retired
No product available!
Integrated circuit - Four White LED Backlight Driver, LFCSP 16 VQ housing, Analog Devices, RoHs
Retired
No product available!
4-channel white LED driver based on the Boost converter; 2.8 ... 18V; 100mA; 12 LFCSP; Analog Devices; Compliance
Retired
No product available!
A 10-bit programmable magnetic object rotation sensor (encoder). It can work at 3.3V and 5V, it has a measurement resolution of 0.35 degrees and a serial and PWM signal output. The system has a SSOP16 housing
Retired
No product available!
The 9DoF module allows measurements of acceleration, angular velocity and direction of the magnetic field. Communication with the system takes place via the I2C bus. modMPU9150 (GY-9150)
Retired
No product available!
No product available!
No product available!
Adafruit 2298
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
KAmodLSM303 is a module that allows you to measure the acceleration and the value of the magnetic field.
Retired
No product available!
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.
Retired
No product available!
ST-LINK in-circuit debugger / programmer for ST microcontrollers