- Out-of-Stock
AVT5132 A +
ID: 190373
PRESSURE FORCE METER - PRINTED PLATES AND PROGRAMMED SYSTEM
PRESSURE FORCE METER - PRINTED PLATES AND PROGRAMMED SYSTEM
Producer: AVT
The device measures the contact force expressed in newtons. A relatively cheap, foil pressure sensor is used as a sensor. Its principle of operation is similar to the sensors used in foil keyboards - the difference is only that instead of switching, the resistance of the button decreases depending on the value of the applied force. So, to read the pressure value, you only need to measure the resistance. Unfortunately, its changes in the force function are not linear, which is included in the program of the PSoC microcontroller being the 'heart' of the meter.
The device is particularly recommended in places and situations where it is worth knowing how much pressure is exerted
Selected parameters:
- range of measured forces 1 to 100 N
- foil, resistive pressure sensor
- readout of the measured value on the LED line or LCD display
- no need to use a complicated calibration procedure
- built-in stabilizer
- power supply - 9-12Vdc
- tile dimensions 84x58mm
- a printed circuit board, programmed layout and documentation in the set
Detailed description in EP 5/08
Download
190373
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. Totem TE-X4-KIT1
Retired
No product available!
Robot controller dedicated to Totem sets. It is equipped with Bluetooth communication, so it can be controlled using a smartphone. TMK-X3K totem
Retired
No product available!
Thermally conductive tape used as a replacement for thermally conductive paste. They are very flexible and characterized by high compressibility. AG Termopasty ART.AGT-161
Retired
No product available!
Li-Po battery with a rated voltage of 3.7 V and a capacity of 1350 mAh, equipped with a PCM protection and a 1.5 JST-ZH connector. Akyga LP503758
Retired
No product available!
Module with a 3-axis MMA8452Q accelerometer. The system has a configurable measurement scale of ±2g/±4g/±8g. It is supplied with the voltage from 1.95 to 3.3 V and communicates via the I2C interface. SparkFun SEN-12756
Retired
No product available!
External enclosure designed to protect, transfer and store data on 2.5” HDD and SSD drives with SATA interface. UGO UKZ-1531
Retired
No product available!
128 GB Hynix SSD. It is equipped with NVMe PCIe 3.0 interface with M.2 B&M Key connector. Hynix HFM128GDHTNG-8310A
Retired
No product available!
Samsung 980 SSD 250 GB. It is equipped with NVMe PCIe 3.0 x4 interface with M.2 M Key connector. Samsung MZ-V8V250BW
Retired
No product available!
External case designed to protect, transfer and store data on M.2 SSD drives with SATA interface. GEMBIRD EE2280-U3C-01
Retired
No product available!
External enclosure designed to protect, transfer and store data on M.2 SSD drives with NVMe or SATA interface. Unitek S1204B
Retired
No product available!
Module with e-Paper display with a diagonal of 2.13" and a resolution of 250x122 px with WiFi communication and Bluetooth 4.2. Waveshare 2.13inch e-Paper Cloud Module
Retired
No product available!
LoRa module based on ESP32-WROOM-32E with WiFi and Bluetooth communication and LoRa RFM95W modem. There are ESP32 pins and a Qwiic connector on the board. SparkFun WRL-18074
Retired
No product available!
A module with a MEMS microphone and an amplifier that will allow you to detect a voice, a clap or a door slam. The board has an analog output. SparkFun BOB-18011
Retired
No product available!
Base board for the SpaceSOM-8Mplus family of modules. Creates a complete development platform similar to the SBC. SoMLabs SpaceCB-8Mplus-ADV v.1.1
Retired
No product available!
50 W soldering iron for Bakon BK950D station. Works with soldering tips from the T13 series
Retired
No product available!
HAT expansion module with SATA interface designed for Raspberry Pi 4 model B. It allows you to connect to a minicomputer mass storage in the form of 2.5" HDDs and SSDs with SATA interface
Retired
No product available!
PRESSURE FORCE METER - PRINTED PLATES AND PROGRAMMED SYSTEM