- Out-of-Stock
AVT2218 A
ID: 193324
EASY TO INSTALL THE CAR ALARM - PRINTED PLATE
EASY TO INSTALL THE CAR ALARM - PRINTED PLATE
Producer: AVT
The system is quite atypical (and convenient to assemble), because it does not need any sensors signaling burglary or attempting to start the car. Just connect it to the vehicle's electrical system and attach the appropriate executive systems: siren, lights, turn signals, etc. The system monitors the voltage in the installation and detects its decrease. This occurs, for example, when the door is opened (internal lighting is on) or attempts to start the engine (starter).
The device is especially recommended for owners of motor vehicles, the simplest and highly electronic ones
Selected parameters:
- built-in voltage drop sensor
- a delay to enable / disable the alarm
- executive element - relay
- possibility of using in vehicles with 'plus' and 'minus' on the mass
- power supply - 12 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available- Detailed description in
- and
Download
193324
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Raspberry PI 4 computer case, transparent black, type VESA + screws
Raspberry Pi 4 computer case made of plastic, transparent black. Raspberry RPI-ENC049-CLR/BLK
Retired
No product available!
Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD
Retired
No product available!
Stabilized laboratory power supply Wanptek with variable voltage regulation in the range from 0 to 30V and current in the range of 0 to 10A. Wanptek KPS3010D
Retired
No product available!
Stabilized laboratory power supply Wanptek with variable voltage regulation in the range from 0 to 30V and current in the range of 0 to 5A. Wanptek KPS305D
Retired
No product available!
Stabilized laboratory power supply Wanptek with variable voltage regulation in the range from 0 to 60V and current in the range of 0 to 5A. Wanptek KPS605D
Retired
No product available!
The eXtremestyle silicone cable (1.5m length) with Lightning connector. Allows you to charge the device and transfer data. eXtreme S15ULB
Retired
No product available!
The eXtremestyle silicone cable (1.5m length) with Lightning connector. Allows you to charge the device and transfer data. eXtreme S15ULW
Retired
No product available!
The eXtremestyle silicone cable (1.5m length) with US Type C connector. Allows you to charge the device and transfer data. eXtreme S15UCB
Retired
No product available!
The eXtremestyle silicone cable (1.5m length) with US Type C connector. Allows you to charge the device and transfer data. eXtreme S15UCW
Retired
No product available!
The eXtremestyle silicone cable (2m length) with micro USB connector. Allows you to charge the device and transfer data. eXtreme S20UMB
Retired
No product available!
The eXtremestyle silicone cable (2m length) with micro USB connector. Allows you to charge the device and transfer data. eXtreme S20UMW
Retired
No product available!
Board with ATmega32U4 and Atheros AR9331. It combines the advantages of a microcontroller and a microprocessor with Linux. The set has 32 KB flash memory, 20 digital inputs / outputs, including the ability to configure 7 as PWM channels and 12 as analog inputs (ATmega32U4) as well as a WiFi module and a microSD card slot (Atheros AR9331). Arduino Yún Rev2
Retired
No product available!
Development board with SAMD21 microcontroller (ARM Cortex® M0+), 8 I/O lines, 12 PWM channels, micro-USB. The board is equipped with the ATA8520 SigFox module enabling the implementation of SigFox communication. Arduino MKR FOX 1200 ABX00014
Retired
No product available!
Board is a board with Atmel ATSAMW25 chip, the system has SAMD21 microcontroller (ARM, Cortex-M0+ core, 256 kB Flash, 8 KB SRAM) treated with 48 MHz clock. The ATSAMW25 chip also includes the WINC1500 Wi-Fi module. The user has at his disposal: 8 I/O lines, 12 PWM channels, 7 analog inputs. Arduino MKR1000 ABX00004
Retired
No product available!
Development board with SAMD21 microcontroller (ARM Cortex® M0+), 8 I/O lines, 12 PWM channels, micro-USB. The board is equipped with the CMWX1ZZABZ module enabling the implementation of communication in Lo-Ra networks. Arduino MKR WAN1300 ABX00017
Retired
No product available!
Development board with SAMD21 microcontroller (ARM Cortex® M0+), 8 I/O lines, 12 PWM channels, micro-USB. The board is equipped with the ATSAMD21 module and SARA-U201 U-blox enabling the implementation of communication in GSM networks. Arduino MKR GSM 1400 ABX00018
Retired
No product available!
EASY TO INSTALL THE CAR ALARM - PRINTED PLATE