- Out-of-Stock
AVT2762 A
ID: 193724
AMPLIFIER FOR TRANSMITTERS N-MOSFET - PRINTED PLATE
AMPLIFIER FOR TRANSMITTERS N-MOSFET - PRINTED PLATE
Producer: AVT
Amplifier on discrete elements, or an alternative to the "cube" TDA7294. The popular power transistors N-MOSFET type IRF540 were used in the power stage. Their parameters make it possible to obtain an output power of 100 W RMS with +/- 50 V power supply at a load of 4 ohms. The system enables the use of IRF640, IRFP240 or IRFP250 transistors in the power amplifier. You can then increase the supply voltage and get a correspondingly higher power (up to 200 W). The amplifier is equipped with protection systems against short-circuiting the output and a silent switching on and off system.
The device is especially recommended for audio device constructors
Selected parameters of the amplifier:
- output power approx. 100 W RMS (+/- 50 V, 4 ohms)
- built-in short-circuit protection
- mute when turning the power on and off
- output current limiter (protection)
- the possibility of using higher power output transistors
- power supply - +/- 50 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available
- Detailed description in
Download
193724
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
You might also like
AMPLIFIER FOR TRANSMITTERS N-MOSFET - A KIT FOR INDEPENDENT INSTALLATION
Delivery date unknown
No product available!
Other products in the same category (16)
Camera board for the STM32F407G-DISC1 set. It allows you to capture an image with a resolution of 1280 x 1024 pixels (1.3MP). The set includes a flexible cable that allows the camera to be connected to the STM32F4DIS-BB expansion board
Retired
No product available!
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. DEV-13687
Retired
No product available!
No product available!
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. Pololu 3170
Retired
No product available!
EXtreme CC312U 3100mA power supply / car charger with two USB ports, allows you to charge phones, navigation, mp3 / mp4 players and connect Raspberry Pi computers
Retired
No product available!
AVT kit for self-assembly of an extremely effective bomb clock. AVT3128 B
Retired
No product available!
AVT kit for self-assembly of the battery capacity meter and the level of battery consumption. AVT5500 B
Retired
No product available!
433M wireless module for SPI interface, vertical pinheaders, 1.27mm pitch
Retired
No product available!
high performance e-compass, 3D accelerometer and 3D magnetometer module, I2C interface, LSM303DLHC on board
Retired
No product available!
three-axis digital output gyroscope, three-axis angular rate sensor module, I2C/SPI interface, L3G4200D on board
Retired
No product available!
High-power brushed DC motor with a 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is perpendicular to the motor shaft, and a built-in safety clutch. Pololu 1511
Retired
No product available!
High-power brushed DC motor, 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, built-in safety clutch. Pololu 1512
Retired
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
AMPLIFIER FOR TRANSMITTERS N-MOSFET - PRINTED PLATE