- Out-of-Stock
These premium wires are stranded 22AWG wires with male terminals on both ends. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 36" (90 cm) wires includes two each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x6-Pin 10-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Adafruit 856 - MCP3008 - 8-Channel 10-Bit ADC With SPI Interface
No product available!
No product available!
Adafruit 833 - Liquid Flow Meter - Brass 1/2" Nominal Threaded
No product available!
Adafruit 804 - PS/2 Wired Connector - Panel Mount MiniDIN-6
No product available!
Adafruit 800 - Netduino Go! Starter Pack (Modular .NET microcontroller)
No product available!
Adafruit 72 - DC Boarduino (Arduino compatible) Kit (w/ATmega328) - v1.0
No product available!
Adafruit 714 - RGB LCD Shield Kit w/ 16x2 Character Display - Only 2 pins used! - NEGATIVE DISPLAY
No product available!
Adafruit 659 - FLORA - Wearable electronic platform: Arduino-compatible - v2
No product available!
No product available!
No product available!
TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cells, this sensor is more precise, allowing for exact lux calculations and can be configured for different gain/timing ranges to detect light ranges from up to 0.1 - 40,000+ Lux on the fly. Adafruit 439
No product available!
Adafruit 286 - LoL Shield GREEN - A charlieplexed LED matrix kit for Arduino - 1.5
No product available!
Adafruit 280 - USB/DC Lithium Polymer battery charger 5-12V - 3.7/4.2v cells
No product available!
Adafruit 274 - LoL Shield RED - A charlieplexed LED matrix kit for the Arduino - 1.5
No product available!
This is a great battery-backed real time clock (RTC) that allows your microcontroller project to keep track of time even if it is reprogrammed, or if the power is lost. Perfect for datalogging, clock-building, time stamping, timers and alarms, etc. Adafruit 264
No product available!
4-digit 7-segment display with MAX7219 driver chip. Adafruit 1268
No product available!