.png)
- Out-of-Stock
Dagu Wild Thumper 6WD chassis, silver, 75:1
ID: 195983
Off-road chassis Dagu Wild Thumper 6WD in silver, complete with wheels with a diameter of 120 mm and engines with a gear 75:1. The chassis is made of aluminum sheet, holes with a diameter of 4 mm spaced every 10 mm allow the installation of the controller and accessories. Pololu 1563
Description
Durable, all-terrain chassis with 6-wheel drive from Dagu Electronics. It has been designed to navigate rough terrain and steep grades, making it the perfect platform for any robot that needs to perform tasks in a harsh environment. The structure is equipped with six DC motors with brass brushes and steel gears 75:1, which drive large wheels with a diameter of 120 mm. The unique 'super-twist' suspension system keeps each wheel in contact with the ground, ensuring maximum traction even when driving on uneven or bumpy surfaces. The suspension can be adapted to different loads and conditions. The housing is made of corrosion-resistant 2mm anodized aluminum plate, all nuts, bolts and screws are stainless steel, and the brass mounts and suspension springs are nickel-plated. At 7.2 volts, the chassis reaches a top speed of around 3 km / h, and each engine has a torque of around 11 kg-cm.
The aluminum chassis plate has 4 mm holes spaced every 10 mm for easy installation of control electronics, sensors and additional equipment, and with a maximum recommended load of 5 kg, the platform is capable of carrying additional cargo. The two compartments on the chassis are designed to hold the 7.2V sub-C batteries that are commonly used in RC cars. These compartments hold a total of four such batteries. The inside of the case also includes convenient screw terminals for connecting the battery leads and engine controller.
Dagu Wild Thumper is a chassis with a differential drive, which means turning is done by driving the motors on both sides of the platform at different speeds. The three motors on each side of the robot are connected in parallel, so only two control channels are needed to run the landing gear. The motors are designed for a maximum rated operating voltage of 7.2 V (minimum 2 V), with a maximum current consumption of 6.6 A.
Features
- Ground clearance: 60 mm
- Maximum recommended load capacity: 5 kg
- Recommended motor voltage: 2 V to 7.5 V
- Maximum current at 7.2 V: 6.6 A per motor
- Idle current at 7.2 V: 420 mA per motor
- No load output shaft speed at 7.2V: 160 rpm
- Torque at 7.2 volts: 11 kg-cm per engine
- Dimensions: 420 x 300 x 130 mm
- Weight: 2.7 kg
195983
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
Pololu Dual G2 High-Power Motor Driver 18v22 is an extension that allows you to control two DC motors designed for Arduino tiles. The motor can be supplied with 6.5 ... 30V voltage and can draw up a maximum current of 22A. Polol 2517
zł419.89
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1362
zł543.99
Delivery date unknown
No product available!
Pololu G2 18v15 High Power is a miniature DC motor controller. Power supply for the controller: 6.5 ... 30 V. Current efficiency of the module: 15 A. The module has protection against back voltage and overvoltages. Pololu 1363
zł600.12
24h
Available quantity: 1
Available
Other products in the same category (16)
Computer with Amlogic S922X processor that integrates the ARM Cortex-A73 quad-core system and the Cortex-A53 dual-core chip with the Mali-G52 graphics processor and 2GB of RAM. Additional equipment includes: Gigabit Ethernet, eMMC memory socket, HDMI 4K, microSD card slot and a 40-pin GPIO connector. Hardkernel Odroid N2
Retired
No product available!
Computer with Amlogic S922X processor that integrates the ARM Cortex-A73 quad-core system and the Cortex-A53 dual-core chip with the Mali-G52 graphics processor and 4GB of RAM. Additional equipment includes: Gigabit Ethernet, eMMC memory socket, HDMI 4K, microSD card slot and a 40-pin GPIO connector. Hardkernel Odroid N2
Retired
No product available!
GoodRam Cl! Ck Pendrive UCL 32GB, USB 2.0 with Push & Pull system
Retired
No product available!
Pendrive GoodRam Cl! Ck UCL2 16GB, USB 2.0, white, Push & Pull
Retired
No product available!
Digital oscilloscope equipped with a 7" TFT LCD display. It has two measurement channels with a 200 MHz bandwidth, a sampling rate of 1 GSa/s and a 14 Mpkt memory buffer. Siglent SDS1202X-E
Retired
No product available!
EDC Speaker cable 10 m, 2 x 0.35 mm red-black colour
Retired
No product available!
Tip 900M-T-0.5C beveled to the station AOYUE ZHAOXIN REPRO YIHUA PT WEP black from ZHAOXIN.
Retired
No product available!
Starter kit with STM32MP157A application microprocessor (combination of a typical processor with Cortex-A7 core and microcontroller with Cortex-M4 core). The system allows users to create applications using the STM32 MPU OpenSTLinux Distribution software for the main processor and the STM32CubeMP1 software for the coprocessor. STMicroelectronics STM32MP157A-DK1
Retired
No product available!
Starter kit with STM32MP157C application microprocessor (combination of a typical processor with Cortex-A7 core and microcontroller with Cortex-M4 core). The system allows users to create applications using the STM32 MPU OpenSTLinux Distribution software for the main processor and the STM32CubeMP1 software for the coprocessor. STMicroelectronics STM32MP157C-DK2
Retired
No product available!
Crimping tool for connectors 0.08-0.5 mm2 AWG 28-20. It has an adjustable downforce and an arm return lock mechanism. SN-01B
Retired
No product available!
Threaded hexagon spacer M2,5, sleeve length 11mm, female-female. The sleeve is made of brass
Retired
No product available!
HAT module with RFM95W 433 MHz system for LoRa / LoRaWAN communication and OLED display, designed for Raspberry Pi minicomputers. Adafruit 4075
Retired
No product available!
RGB LED matrix module with 64 APA102-2020 diodes in 8x8 arrangement. It is powered by 5V by the pads located on the bottom of the board and controlled by the SPI interface. SparkFun COM-15047
Retired
No product available!
MP3 player module controlled by the I2C interface. It is based on a class D amplifier with a power of 1.4 W. The board has a 3.5 mm headphone output and an 8 Ω speaker connector. Audio files are saved on the microSD card. SparkFun DEV-15165
Retired
No product available!
Module with DRV2605L vibration motor controller and Y axis LRA motor. It allows you to add haptic feedback (vibration effect). SparkFun ROB-15181
Retired
No product available!
Module with a current and voltage sensor. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. SparkFun SEN-15176
Retired
No product available!
Off-road chassis Dagu Wild Thumper 6WD in silver, complete with wheels with a diameter of 120 mm and engines with a gear 75:1. The chassis is made of aluminum sheet, holes with a diameter of 4 mm spaced every 10 mm allow the installation of the controller and accessories. Pololu 1563