- Out-of-Stock
Futaba J Connector Pack, Male
This pack contains everything Futaba J connectors - the connectors. Futaba servos - it's custom cables. You can use a crimping tool to attach your 22-26 AWG wires. This pack contains enough pins and crimp pins (including 3 spare pins) for 3 male connectors . The crimp pins have gold-flashed male contacts.
This Futaba J connector has a 0.1 "pin spacing and mates with connectors on the right Futaba J connectors, and it is also compatible with female JR connectors, which are not keyed. This pack contains three female JR housings, three male Futaba J shrouds, and twelve gold-flashed crimp pins, which is enough for the three male connectors. The crimp pins are designed for 22-26 AWG wires, and we sell a crimping tool that works well with your own custom servo cables or servo extension cables.
This is the assembly of the connectors, push the crimped male pins to the place (the prongs will protrude out of the socket sockets), side of the house with the crimp pin latches faces. If you have done things right, you will hear a snap, and it will lock in place. Note that if you have a JR connector, you can leave the shroud off.
We also sell JR connectors, which are very similar to the premade servo extension and splitter cables.
Note: these connectors are commonly referred to as "female" in the JR connectors below to make sure they are what you want.
|
|
![]() | Futaba J Connector Pack, Female |
![]() | Crimping Tool: 0.1-1.0 mmÂ? Capacity, 16-28 AWG |
![]() | JR Connector Pack, Female |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
No product available!
MYIR MYC-C7Z020 is a single board computer module based on the MYC-C7Z020 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Camera module with a resolution of 13 MP equipped with an image sensor AR1335. The camera has a FoV 100° lens with M12 mount. ArduCAM B0245
No product available!
Soldering tape used to collect excess tin with a gray 1.5 mm, 1.5 m long
No product available!
7\'\' Powertip LCD-TFT 800x480 px display with touch-panel, LED backlight, DC/DC converters, compatible with SoMLabs VisionSTK-xx and VisionCB base boards. SL-TFT7-TP-800-480
No product available!
UART GPS Module, NEO-7M-C is a module containing the U-blox NEO-7M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART interface signal outputs. Waveshare UART GPS NEO-7M-C
No product available!
Starter kit containing Raspberry Pi 4B 8 GB and all necessary accessories: 32 GB microSD memory card with Rasberry Pi OS system, ruler, Ethernet cable and official accessories: housing, cooling kit, power supply and HDMI cable
No product available!
No product available!
Programmable BT4.0 module with UART 2x4 pin 2.54 mm UART connector
No product available!
Green, aluminum case for Raspberry Pi 4 model B. It has been equipped with mounting holes of the VESA 75 standard
No product available!
Futaba J Connector Pack, Male