- Out-of-Stock
Pololu TReX Jr Dual Motor Controller DMC02
This lower-power, smaller, and lower-cost version of the TReX is the ultimate general-purpose motor controller for small motors: it has a wide operating range (5 to 24 V), delivers 2.5 A continuously per motor, provides current sensing on the two main channels, and it features the TReX triple interface that allows you to control motors from a serial line (RS-232 or TTL), radio control (RC) receiver, or analog voltage source such as a potentiometer.
![]() |
| Pololu TReX Jr bottom with labels and dimensions |
|---|
The TReX Jr Dual Motor Controller, a lower-power version of the TReX Dual Motor Controller, is a versatile DC motor controller designed to seamlessly blend autonomous and human control of small robots. The TReX Jr can control two bidirectional and one unidirectional motor via three independent control interfaces: radio control (RC) servo pulses, analog voltage, and asynchronous serial (RS-232 or TTL). Using the compact MC33887 motor driver allows for a single-board design that reduces cost while maintaining a small package. As an added benefit, the use of the MC33887 motor driver allows operation to 24 V.
The TReX Jr uses five input channels to receive the RC or analog control signals. When operating in RC or analog mode, the five channels function as follows:
The serial interface can switch instantly with one of the other two interfaces, allowing mixed autonomous and remote control. For example, a robot could be configured to run autonomously most of the time, but a human operator could override the autonomous function if the robot gets stuck or into a dangerous situation. If the serial mode is selected as the primary interface, high-resolution measurements of all five channel input signals (be they RC pulses or analog voltages) are made available to the autonomous robot controller, allowing for complex and unlimited mixing of operator control and sensor input. For example, the TReX would be a great motor controller for a remotely controlled balancing robot.
![]() |
| Pololu TReX Jr Dual Motor Controller with labels |
|---|
| Dimensions | 1.75" x 1.75" x 0.5" (0.3" height without connectors) |
| Supply voltage | 5 – 24 V |
| Primary motor outputs | 2 bidirectional, 5 A peak, up to 2.5 A continuous (may be combined to control 1 bidirectional, 5 A continuous) |
| Auxiliary output | 1 unidirectional, 10 A continuous |
| Speed control | 128 steps in each direction |
| Control interfaces | RC servo pulses, analog voltages, or serial commands; master interface set by mode-select jumper |
| Input channels | 5 (RC servo pulses or analog voltages) |
| RC pulse measurements | 12-bit resolution, 1 us accuracy |
| Analog measurements | 10-bit resolution |
| Serial interface | both RS-232 and TTL (logic level), bidirectional |
| Baud rates | supports 11 common baud rates ranging from 1200 to 115,200 bps |
| Expanded protocol | Allows multiple Pololu servo and motor controllers on one serial line |
| Compact protocol | Allows both motors 1 and 2 to be simultaneously set with just three bytes |
Note: The TReX Jr does not require use of the serial interface to function; it will work right out of the box as an electronic speed control (ESC). You will not have access to the full suite of features the TReX Jr provides if you do not make use of the serial interface, though.
![]() |
| 24" (600 mm) female-female RC servo extension cable. |
|---|
The TReX Jr has male 0.1" headers; for direct connection to an RC receiver or serial servo controller, we recommend ordering one 6" female-to-female cable, 12" female-to-female cable, or 24" female-to-female cable per channel you intend to use (the TReX Jr can use up to five channels).
![]() |
Servo Extension Cable 6" Female - Female |
Data sheet
Manufacturer
Responsible person
Module with a digital barometer DPS310. It enables pressure measurement in the range from 300 to 1200 hPa and communicates via I2C or SPI. Adafruit 4494
No product available!
Module with a 6-axis IMU sensor (accelerometer and gyroscope) that allows you to measure acceleration and rotational speed in a wide range of ±30g and ±4000dps. Communicates via I2C. Adafruit 4464
No product available!
Module with WM8960 audio decoder that allows you to operate 1 W stereo speakers and two microphones via the I2S interface. Adafruit 4757
No product available!
Module with WiFi Espressif ESP32-S2. It integrates two 3.3 V stabilizers, SPI Flash memory, LiPo charging circuit, light sensor and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4769
No product available!
Wireless temperature and humidity sensor. It allows you to track changes in temperature and humidity in your home. Shelly H&T BLACK
No product available!
HAT module with MCC 118 chip, designed for Raspberry Pi. Provides 8 analog inputs with a resolution of 12 bits, sampling rates up to 100 kS/s and range +/-10 V. Digilent 6069-410-000
No product available!
HAT MCC 128 module for Raspberry Pi. Provides 8 analog inputs with a resolution of 16 bits, sampling rates up to 100 kS/s and a range of +/-10 V, +/-5 V, +/-2 V, or +/-1 V. Digilent 6069-410-001
No product available!
HAT MCC 134 module for Raspberry Pi. Provides 4 inputs with a resolution of 24 bits dedicated to thermocouples type J, K, R, S, T, N, E or B. Digilent 6069-410-002
No product available!
HAT MCC 152 module for Raspberry Pi. It provides 2 analog outputs with a resolution of 12 bits and a range of 0-5 V and 8 digital inputs/outputs. Digilent 6069-410-003
No product available!
HAT MCC 172 module for Raspberry Pi. Provides 2 inputs with 24 bit resolution for IEPE sensors such as accelerometers and microphones. Digilent 6069-410-004
No product available!
HAT MCC 172 module for Raspberry Pi. Provides 2 inputs with 24 bit resolution for IEPE sensors such as accelerometer and microphone. Two coaxial cables are included. Measurement Computing MCC 172
No product available!
High voltage differential probe. It is characterized by good measurement parameters: with a 100 MHz band and an operating voltage up to 700 V. The probe has two attenuation factors: 10X and 100X. Micsig DP10007
No product available!
The expansion board with the LoRaWAN SX1302 and GNSS L76B module is dedicated to Raspberry Pi minicomputers. The kit includes the 868M antenna, GPS and necessary cables. Waveshare SX1302 LoRaWAN Gateway HAT
No product available!
The module with the LoRaWAN ASR6501 system and an external antenna, designed for the M5Stack sets. M5Stack U117
No product available!
The LoRaWAN SX1302 module is equipped with a Mini-PCIe connector. It uses the SPI or I2C interface for communication. Waveshare SX1302 868M LoRaWAN Gateway
No product available!
Alkaline battery A27 12V 7.6x27.3 mm with a capacity of 25 mAh
No product available!
Pololu TReX Jr Dual Motor Controller DMC02