- Out-of-Stock
XF-ABS wire 1.75 mm - orange fluor, is a high quality wire for your 3D printer. The material does not undergo severe shrinkage during printing, making it easier to print spatial objects. The material adheres very well to the printer platform, which does not cause the so-called "First-layer problem".
Wire color: XF-ORANGE FLUOR
Printing technology: FFF (Fused Filament Fabrication)
Application: all 3D printers, with an open RepRap architecture, printing a 1.75 mm filament
Description: coil of wire on a net weight scale ~ 1kg total weight with reel ~ 1,3kg, biodegradable reel
Color: XF-orange fluor
Printing temperature: 225-235 ° C
Properties: made of the original material without admixtures from the milling, low resistance of extrusion, uniform color, suitable for making prototypes, very good dimensional tolerance +/- 0.05 mm
Manufacturer
Responsible person
Easy PLA filament in yellow, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Yellow
No product available!
Kit with LS1046A Freeway development board equipped with 4-core LS1046A processor, 4 GB RAM, 4GB Flash, 4 Gigabit Ethernet connectors, 2 USB 3.0 connectors, microSD slot and two M.2 slots. NXP FRWY-LS1046A-AC
No product available!
ABS filament in yellow with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy ABS Yellow
No product available!
Adapter for connecting a Raspberry Pi to the OM-SE050ARD development board. It allows you to run the EdgeLock SE050 application on a Raspberry Pi. NXP OM-SE050RPI
No product available!
LPC55S69JEV98K, ARM Cortex-M33 Microcontroller, 32 bit, 150 MHz, 640 KB Flash, VFBGA98
No product available!
USB - CAN converter module. It allows the device to be connected to a computer (USB) or microcontroller (UART) via the CAN bus. USB CAN CONVERTER (UCCB)
No product available!
Set with HQ camera, HDMI adapter, lens, tripod and Jetvariety adapter. Kit designed for NVIDIA Jetson Nano. ArduCAM B0243
No product available!
Laboratory power supply with programmable memory and smooth voltage regulation in the range from 0 to 60V and smooth current regulation in the range from 0-5A. KORAD KD6005D
No product available!
Industrial SoC module integrating Xilinx Zynq 7020 SoC, Gigabit Ethernet transceiver, 1 GB DDR3 SDRAM and 32 MB Flash memory. Trenz Electronic TE0720-03-2IF
No product available!
A minisumo robot on a tracked chassis with Pololu 100:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3127
No product available!
A module that allows you to connect ArduCAM cameras with a CSI interface to a PC or minicomputers via the USB3.0 interface. It not only supports high-resolution, high-frame rate image sensors, but also a stereoscopic camera and IRCUT control functions. ArduCAM B0111
No product available!
A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 1 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 1GB
No product available!
A small minicomputer with a RockChip RK3328 quad-core SoC chip (ARM Cortex-A53). The computer is equipped with 2 GB DDR4 RAM, Gigabit Ethernet port and USB 3.0. Each module has its own unique MAC address. NanoPi NEO3 2GB
No product available!
White case for the NanoPi NEO3 minicomputer. It allows easy access to the Ethernet connector, USB, microSD cards and the power connector. FriendlyELEC Case for NEO3
No product available!
HDMI to CSI-2 bridge module based on TC358840 chip. It has a 22-pin FPC connector with a pitch of 0.5 mm and an audio connector. The input signal is supplied through the HDMI connector. Auvidea 70511
No product available!
Image capture module for Raspberry Pi. Captures high definition video from digital (HDMI/DVI), analog (YPbPr component) and computer (RGB) sources in 480p, 720p and 1080p. Picapture HD1
No product available!
High quality XF-ABS filament for 3D printer with 1.75 mm diameter. 1 kg of wire is wound on the spool.