- Out-of-Stock
Motion detection and light intensity module Gesture Explore
ID: 560101
5906623411245
The plate allows the detection of gestures, similar objects at a distance of a few to several centimeters and the intensity of ambient light, equipped with an APDS-9960 system with an I2C interface. MOD-66
Description
The module allows for the detection of gestures, similar items at a distance of a few to several centimeters and the intensity of ambient light. It has a built-in APDS-9960 chip (Avago Technologies *) with an I2C interface. The configuration jumper V_SEL +3,3 V / + 5 V enables selection of supply voltage and digital signals.
Attention!
The standard setting of the power jumper is +3.3 V.
Modulowo® DuoNect ™ solution
The Modulowo® DuoNect ™ solution enables fast and easy connection of expansion modules to Arduino , Raspberry Pi , Intel® Edison , STM32 Nucleo , Atmel Xplained , TI LaunchPad , Freescale Freedom and other platforms.
properties
- Built-in APDS-9960 chip
- Compliance with Modulowo® DuoNectTM
- I2C interface
- edge and through leads with 2.54 mm pitch
- Additional outputs with a 2.0 mm grid
- Space for the system to identify the module
- Built-in translator of signals + 3.3 V / + 5 V
- Supply voltage: + 3.3 V / + 5 V
- Dimensions: ~ 26 mm x 24 mm
- Compliance
Included
- Module MOD-66
- A set of connectors for self-assembly
To download
560101
Data sheet
- Interface
- I2C
- Type of sensor
- Laser
- Minimum distance
- 10 cm
- Maximum distance
- 20 cm
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
The SparkFun Qwiic Shield for Arduino Nano allows you to add the SparkFun Qwiic ecosystem to development boards that use the Arduino Nano Footprint in an easy-to-assemble shield. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Arduino Nano to four SparkFun Qwiic connectors.
Retired
No product available!
The SparkFun Qwiic Shield for Thing Plus provides an easy-to-assemble way to add the SparkFun Qwiic ecosystem to any development board with the Thing Plus Footprint. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Thing Plus to four SparkFun Qwiic connectors. Sparkfun DEV-16138
Retired
No product available!
Cytron 0.8Amp 5V-26V DC Motor Driver Shield - DC motor driver for Arduino
Retired
No product available!
No product available!
No product available!
No product available!
Cytron USB to UART Converter CH340 - USB - UART converter based on the CH340 chip
Retired
No product available!
Logic level converter (4 channels)
Retired
No product available!
The Blebox Wifi controller is dedicated to the most modern digital tapes with 5 V and 12 V, but a LED strip with WS2812 / WS2811 driver is required. BleBox pixelBox
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, camera, display and Micro SD card connectors. Designed for AI applications in IoT. Seeed Studio 102991150
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, OV2640 camera, LCD display. The set is enclosed in a housing. Designed for AI applications in IoT. Seeed Studio 110991191
Retired
No product available!
MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153
Retired
No product available!
Module with RISC-V Dual Core 64bit chip for AI applications with a wide selection of peripheral systems. It enables the implementation of advanced projects using image recognition, sounds and deep learning. Version without WiFi. Seeed Studio 114991695
Retired
No product available!
Module with RISC-V Dual Core 64bit chip for AI applications with a wide selection of peripheral systems and the ESP8285 WiFi system. It enables the implementation of advanced projects using image recognition, sounds and deep learning. Version with WiFi. Seeed Studio 114991684
Retired
No product available!
The plate allows the detection of gestures, similar objects at a distance of a few to several centimeters and the intensity of ambient light, equipped with an APDS-9960 system with an I2C interface. MOD-66