- Out-of-Stock
Scale module with load cell up to 2kg
ID: 579289
5906623495566
Scale module with aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has screw terminals. Can be used to make electronic scale. KAmodTENSOMETER2kg
Description
Scale module with load cell. Plexi base and measuring area. Allows you to measure weight up to 2 kilograms. Screw terminals for easy connection. Good for edu
Properties
- Weight measurement up to 2 kg
- Supply voltage: 5V DC
- Input resistance: 1115 Ω
- Output resistance: variable (no load: 1000 Ω)
- Base dimensions: 100 x 70 mm
- Height: 33 mm
- Measuring area diameter: 64mm
579289
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The module allows you to attach a strain gauge (working in the Wheatstone bridge circuit) and convert the analog signal into its digital representation, available on the module output lines. The system processes the signal with a 24-bit resolution and can be powered by 2.7V - 5.5V. The module is especially recommended for constructing digital scales in combination with Arduino
zł4.69
24h
Available quantity: 31
Available
Simple-to-use, open source solution for measuring weight and temperature with the ability to read multiple types of load cells and offers a simple-to-use serial menu to configure calibration value, sample rate, time stamp and units of precision. SEN-13261
zł178.41
24h
Available quantity: 2
Available
Other products in the same category (16)
Pin strip straight in black, double-breasted, female, 2x4, pitch 2.54mm, THT, RoHS. PBD08S
Retired
No product available!
No product available!
Female terminal block, 5-pin. Pitch 3.5mm. Height 15.6mm. KF2EDGK
Retired
No product available!
Filament from ROSA3D made of high-quality PLA pellets. Placed on a cardboard thimble, on which 1 kg of 1.75 mm diameter filament is wound. ROSA3D ReFill PLA Starter Green
Retired
No product available!
Fully programmable card (PICC) emulator, simulator to characterize, test and certify contactless readers for ISO 14443, ISO 15693, NFC and FeliCa conformity
Retired
No product available!
Module with a water level sensor with a measuring range of up to 10 cm. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020635
Retired
No product available!
A needle with a diameter of 0.4 mm, designed for cleaning the nozzle in 3D printers. It allows you to get rid of the remnants of the material after printing and to remove the filament in case of clogged nozzle
Retired
No product available!
No product available!
Banachowski Lech, Diks K.rzysztof, Rytter Wojciech
Delivery date unknown
No product available!
No product available!
Camera module 0.3 Mpx with the Aptina Imaging MT9V111 CMOS sensor with a matrix resolution of 640 x 480 pixels and transmission speeds in the VGA format up to 30 FPS. Adapted to work in low light conditions. Communication via a parallel interface. ArduCAM B0059
Retired
No product available!
A pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin output for connecting a minicomputer and five sets of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM320
Retired
No product available!
Assembled a large XXL thermometer, measuring the temperature in the range from -55 ... + 125 ° C. AVT1790 C
Retired
No product available!
No product available!
No product available!
No product available!
Scale module with aluminum tensometer beam, allowing weight measurement up to 2 kilograms. It has screw terminals. Can be used to make electronic scale. KAmodTENSOMETER2kg