- Out-of-Stock
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16344
GPS module with u-blox ZED-F9R. The module uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. The ZED-F9R module can receive signals from the GPS, GLONASS, Galileo and BeiDou constellations with an accuracy of 0.2 meters (supports simultaneous reception of four GNSS systems). The module provides position accuracy in cities or in covered areas. Continuous positioning is ensured even under weak signal conditions and is available in the event of total signal loss (e.g. short tunnels and garages). The ZED-F9R is an excellent solution for autonomous robots that require accurate positioning in difficult conditions.
Attention!
For proper operation, the module requires a GPS antenna, which is not included in the set. It must be purchased separately.
The board also has two Qwiic connectors and a USB Type-C connector for communication with the system.
Manufacturer
Responsible person
Antenna with built-in LNA amplifier with high sensitivity, for mounting in a device using a GPS module. The antenna has a 75mm cable, terminated with a U.FL plug (IPEX). Dimensions of the device: 25 x 25 x 4 mm
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
The WEP 995D soldering station is a station consisting of a hot air soldering iron and a tip soldering iron (75 W). It has a PID controller, LCD display, adjustable temperature and air blow out provided by the fan located in the flask. It is used for soldering and desoldering electronic components such as: SOIC, CHIP, QFP, PLCC, BGA, SMD. WEP 995D
No product available!
WEP 853AA soldering station is a combination of hotair and heater. It is equipped with, among others, control of set parameters using a microcomputer, fast heating to a set temperature, and convenient regulation of air flow and temperature. It is used for safe soldering of temperature sensitive components QFP, PLCC, BGA. WEP 853AA
No product available!
The WEP 968DA + soldering station is a hot air station and a soldering iron with LED display. It is equipped with a SAMSUNG microprocessor that checks the station\'s operating parameters and corrects them to the set values. The station is suitable for soldering and desoldering electronic components such as SOIC, CHIP, QFP, PLCC, BGA, SMD. WEP 968DA+
No product available!
The WEP 852D + SE soldering station is a hot air station for soldering of electronic systems, e.g. BGA, SMD, etc., and a 75W tip soldering station. Both station modules can work independently of each other. The wide application and minimal failure rate of the device gives it a leading position on the market of soldering stations. WEP 852D+SE
No product available!
The WEP 898DB soldering station is a small and functional tool designed for professional work. It has a hot air and tip soldering iron, has the ability to adjust the temperature and air blast power and two LED displays showing the temperature for both soldering irons. WEP 898DB
No product available!
WEP 938 soldering station is a powerful soldering iron that quickly reaches the set temperature and quickly compensates for heat loss during operation. Thanks to this, you can solder at a lower temperature compared to cheaper soldering irons with slow temperature compensation. The station has the functions: temperature memory, sleep function, automatic shutdown. WEP 938
No product available!
WEP 878D soldering station is a station with hot air soldering iron (hotair) and 50W soldering iron. It is used in electronic services for safe soldering QFP, BGA, SMD, PLCC and other temperature sensitive components. WEP 878D
No product available!
No product available!
Audio cable with 3.5 mm 3-pin minijack and 2x RCA (chinch), 0,2 m length. GEMBIRD CCA-406
No product available!
Audio cable with 3.5 mm 3-pin minijack 2 m length. GEMBIRD CCA-423-2M
No product available!
Patchcord cable, cat. 5e, with RJ-45 plugs, gray, 2 m long. Equip 225411
No product available!
Cable with USB typ A and microUSB typ B connectors, cable length 0.5 m. LANBERG CA-USBM-
No product available!
Cable with USB type A and microUSB plugs type B 2.0, cable length 0.5 m. LANBERG CA-USBM-10CC-0005-BK
No product available!
Cable with USB typ A and microUSB typ B connectors, cable length 1.8 m. EQUIP
No product available!
Cable with USB typ A and USB typ C connectors, max. current 3A (36W) cable length 1m. GEMBIRD CCP-USB3-AMCM-1M
No product available!
Cable with USB typ C connectors, cable length 1.8m. Lanberg CA-CMCM-31CU-0018-BK
No product available!
GPS module with u-blox ZED-F9R. Uses Automotive Dead Reckoning (ADR) technology. Provides highly accurate and continuous positioning by combining the 3D IMU sensor, vehicle dynamics model, correction data and GNSS measurements. SparkFun GPS-16344