- Out-of-Stock
1.75 mm PLA filament for 3D printing by ROSA3D. 0.8 kg of filament is wound on the spool. The recommended printing temperature is in the range from 185°C to 225°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
PLA is the basic material used in 3D printing. PLA Starter is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable biopolymer. It was made of ingredients approved for contact with food.
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
No product available!
FRAM memory with a capacity of 4kbit by Cypress Semiconductor, communicates via the I2C bus, the power supply voltage is in the range 2.7 - 3.6V. The system has an SOIC8 housing
No product available!
A small Li-Pol battery with a nominal voltage of 3.7 V and a capacity of 1350 mAh. Leaded wires, dimensions: 5 x 37 x 59 mm. Akyga LP503759
No product available!
Thermistor for THT assembly with a resistance of 10k, a temperature coefficient of 3380K and accuracy of 1%. The sensor body is Ø2.5x4mm
No product available!
KAmduino UNO is a development board with functionality and dimensions typical for Arduino UNO. Thanks to the built-in ATmega328P microcontroller and the FT231X chipset, the board can be programmed via a USB interface using the Arduino environment. KAmduino UNO
No product available!
K64 microcontroller with ARM® Cortex®-M4 core, 1MB Flash memory, 256kB RAM, 120MHz, SPI, I2C, I2S, UART, CAN, USB OTG, ADC, DAC, RTC, DMA, LQFP100
No product available!
SmartLED Shield driver (V4) for SmartMatrix series displays, for use with Teensy 3.2, Teensy 3.5 and Teensy 3.6. It is also possible to connect LED Dotstar or APA102 displays. Adafruit 1902
No product available!
Add motion, direction and orientation sensing to your wearable FLORA project with this high precision 9-DOF sensors: 3-axis accelerometer, 3-axis magnetometer and 3-axis gyroscope. Adafruit 2020
No product available!
Ambient Light Sensor, SI1145, connects to the I2C bus pads. Adafruit 1981
No product available!
Extension for Raspberry Pi; communication module with RS-485 interface (DEV-13000). Module with the possibility of mounting the DB-9 socket, the socket should be purchased separately
No product available!
FreeSoC2 board has two processors on-board: a CY8C5868LTI-LP039 and a CY8C5888AXI-LP096. The former serves as a debugger/programmer for the latter, which is the target upon which your application code will be installed. Both parts contain a Cortex-M3 processor core, 256kB of flash memory, 64kB of SRAM, and 2kB of EEPROM. DEV-13229
No product available!
32-bit microcontroller with ARM Cortex-M4 core, XMC4200 family, 256kB Flash, VQFN-48, Infineon
No product available!
No product available!
Translator of TI voltage levels, bidirectional (no signal required to control the flow direction), 8-Bit, especially recommended for use in Push-Pull and Open-Drain systems. The system has a TSSOP20 housing
No product available!
Aluminum extensometer beam, allowing measurement of weight up to 1 kilogram. It has four wires. It is used in kitchen scales and portable scales.
No product available!
Aluminum extensometer beam, allowing weight measurement up to 3 kilograms. It has four wires. It is used in kitchen scales and portable scales.
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Blue Pearl