![J-Link Pro (8.12.00)](https://kamami.pl/86995-large_default/j-link-pro-8-12-00.jpg)
![J-Link Pro (8.12.00)](https://kamami.pl/86995-large_default/j-link-pro-8-12-00.jpg)
zł4,623.90 tax excl.
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
J-Link Pro (8.12.00)
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
Link Pro is a refined version of the regular J-Link. It has an Ethernet interface in addition to the USB interface, as well as two additional LEDs which are used as hardware status indicators.
It connects via Ethernet or USB to the Windows (Windows 2000 and later) PC host.
J-Link Pro is fully compatible with J-Link and can be used "out-of-the-box". J-Link Pro uses DHCP per default. The built-in webserver makes manual configuration easy and convenient. Ethernet allows using the emulator far away from the PC in a development or production environment; download and debugging speed is higher and Ethernet provides electrical isolation from the PC.
All features of the regular J-Link also apply to this product.
Features
Contents
Download:
Code:J-Link Pro/JLINK PRO (8.12.00)
Patchcord UTP 5E Ethernet cable with a length of 2 m - red, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 2 m - black, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 2 m - blue, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 2 m - yellow, with 2xRJ45 connectors
No product available!
Patchcord UTP 5E Ethernet cable with a length of 3 m - gray, with 2xRJ45 connectors
JTAG interface galvanic separator that protects equipment against damage caused by potential differences, with a maximum clock frequency of 110 MHz, 3-5 V power supply, and isolation voltage up to 1 kVDC, equipped with multiple connectors and optical status signaling
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
No product available!
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
J-Link Needle Adapter - connect J-Link to a PCB, Segger
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
J-Link BASE is a USB powered debug probe supporting a large number of CPU cores. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-link BASE Compact (8.19.00)
Adapter with galvanic isolation for STLINK-V3SET. It also allows the programmer to work with systems powered with voltages below 3.3 V. STMicroelectronics B-STLINK-ISOL
No product available!
No product available!
JTAG interface for microcontrollers with ARM core
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
No product available!
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
A tool for debugging and programming STM32 microcontrollers via JTAG/SWD interfaces. It has a built-in current measurement unit (SMU) designed to optimise power consumption. STMicroelectronics STLINK-V3PWR
No product available!
Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)
An adapter dedicated to programming STM32 microcontrollers in QFP100 chassis. It has a 20-pin JTAG/SWD connector and/or a 4-pin USART1 interface for programming and testing. Waveshare STM32-QFP100
A tool for programming and debugging applications for systems with the ARM Cortex-M and ARM Cortex-A core. It uses an embedded GDB server that is emulated via USB. Adafruit 3839
No product available!
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger