10-wire ribbon cable for Segger J-Link EDU mini
ID: 565483
zł34.42
Tax included
zł27.98 tax excl.
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
This cable allows to connect J-Link EDU mini (JTAG connector pitch: 1.27mm) to every Development Board with IDC20 connector 2.54mm pitch.
Features
- 10-wire ribbon cable, 2x5 pin, 50 mil to IDC20 2.54 mm pitch
- Lenght: 19cm
- Compatible with programmer J-Link EDU mini
565483
You might also like
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
zł280.07
24h
Available quantity: 18
Available
Other products in the same category (16)
An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)
zł260.56
4 weeks
No product available!
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
zł1,052.90
4 weeks
No product available!
No product available!
JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)
zł3,164.25
24h
Available quantity: 2
Available
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
zł1,052.90
4 weeks
No product available!
The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)
zł260.56
4 weeks
No product available!
JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)
zł5,235.25
24h
Available quantity: 1
Available
No product available!
Available
Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)
zł521.14
4 weeks
No product available!
Flash programmer for ST7 series of flash microcontrollers with on-chip flash
zł3,179.97
4 weeks
No product available!
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
zł280.07
24h
Available quantity: 18
Available
No product available!
A power adapter that provides a stabilized supply voltage to the target board (can be adjusted from 3.6V to 0.8V). Segger Target Supply Adapter (8.06.18)
zł361.60
4 weeks
No product available!
J-Link Needle Adapter - connect J-Link to a PCB, Segger
zł521.14
24h
Available quantity: 13
Available
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł3,432.39
24h
Available quantity: 3
Available
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini