8-channel Bi-directional Logic Level Converter - TXB0108, RoHS
Description
Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that they need to perform level shifting/conversion to protect the 3.3V device from 5V.
Although one can use resistors to make a divider, for high speed transfers, the resistors can add a lot of slew and cause havoc that is tough to debug. For that reason, we like using 4050/74LVX245 series and similar logic to perform proper level shifting. Only problem is that they are only good in one direction which can be a problem for some specialty bi-diectional interfaces and also makes wiring a little hairy.
That's where this lovely chip, the TXB0108 bi-directional level converter comes in! This chip perform bidirectional level shifting from pretty much any voltage to any voltage and will auto-detect the direction. Only thing that doesn't work well with this chip is i2c (because it uses strong pullups which confuse auto-direction sensor). If you need to use pullups, you can but they should be at least 50K ohm - the ones internal to AVRs/Arduino are about 100K ohm so those are OK! Its a little more luxurious than a 74LVX245 but if you just don't want to worry about directional pins this is a life saver!
This breakout saves you from having to solder the very fine pitch packages that this chip comes with. We also add 0.1uF caps onto both sides and a 10K pull-up resistor on the output enable pin so you can use it right out of the box!

Documents
Manufacturer
Responsible person
BOB-11771 Voltage-Level Translator - TXB0104 Breakout
No product available!
No product available!
Module with a 4-bit bi-directional voltage level converter. It allows you to connect digital interfaces with different operating voltages. KAmodNTS0104PW
Analog voltage divider module. It enables a 5-times reduction of the input voltage. DFRobot DFR0051
No product available!
Bi-directional 8-channel logic level converter module (1.2-3.6V to 1.7-5.5V) based on TXS0108 chip.
Bi-directional 8-channel logic level converter module (1.2-3.6V to 1.7-5.5V) based on TXB0108 chip.
A module with a set of resistors and mechanical switches that allows you to adjust the resistance in the range from 0 to 999990 Ω. SparkFun KIT-13006
No product available!
Module with a bidirectional converter for the I2C bus, based on the PCA9306 system. It allows you to connect two I2C modules operating with different voltage levels. SparkFun BOB-15439
No product available!
Module with a voltage level converter 3.3 V - 5 V intended for use in the Qwiic system. It has a built-in Step Up converter providing power supply with a voltage of 5 V and a current of up to 100 mA. SparkFun SPX-17238
4-channel converter of voltage levels 3.3V/5V that allows you to connect systems operating at a lower voltage to those powered by a higher voltage
Voltage-to-current converter module designed for devices with a current signal input. It allows you to linearly convert voltage signals from 0 to 5 V into current signals from 0 to 20 mA
No product available!
4-channel converter of logic levels allowing for connection of systems operating with voltage levels of 1.8 V, 2.5 V, 3.3 V and 5 V. DFRobot DFR0843
8-channel voltage level converter allowing for connection of systems operating with the voltage level of 1.8 V, 2.5 V, 3.3 V and 5 V. SparkFun BOB-19626
Module with a voltage level converter from 5 V to 3.3 V, intended for use in the STEMMA QT/Qwiic system. It has a built-in voltage stabilizer providing 3.3 V power supply with a current of up to 500 mA. Adafruit 5637
3V/5V voltage level converter module with built-in Step-Up converter. Allows development boards operating at 3V to be connected to a device requiring a higher operating voltage of 5V for I2C communication. Adafruit 5649
8-channel voltage level converter module with an input voltage of 12 V and an output voltage of 3.3 V. Unidirectional, based on resistor dividers. Numato Lab NLVD00008
A module enabling the conversion of input voltage in the range from 1.8 V to 5.3 V into the appropriate negative output voltage. It offers high efficiency in excess of 80%, making it ideal for applications where a lower power negative supply is required, such as biasing sensors or op-amp circuits. Pololu 2839
A small module with a voltage level converter that allows easy conversion of signals from 3.3V to 5V. It is compatible with a wide range of LED strips, such as NeoPixel. With easy, solderless installation, it supports up to two signal lines, ensuring smooth operation of LEDs at frequencies up to 10 MHz. Adafruit 6066
8-channel Bi-directional Logic Level Converter - TXB0108, RoHS