Board with the DA16200 module, i.e. an integrated WiFi module with a very low power consumption. Has a built-in chip antenna. The board has a Qwiic connector, a LiPo battery connector, numerous GPIO outputs and a JTAG interface. The module is certified for IEEE802.11b /g/n, WiFi Direct and WPS functions and is an excellent solution for IoT projects. Great for door locks, thermostats, sensors, pet trackers, and other home projects. Full documentation with examples of use is available on the product page.
SparkFun Thing Plus - DA16200 Features
PWR - Red 3.3V power indicatorCHG - Yellow battery charging indicatorSTAT - Blue status/test LED (GPIO 4)IOC7DA16200MOD General Features:
Data sheet
Manufacturer
Responsible person
Cable with USB typ A and USB typ C connectors, cable length 0.5 m. LANBERG
Cable with USB typ A and USB typ C connectors, cable length 1 m. LANBERG CA-USBO-10CC-0010-BK
Cable with USB typ A and USB typ C connectors, cable length 1,8 m. LANBERG CA-USBO-10CC-0018-BK
The expansion board (shield) with the DA16200 WiFi module. It is equipped with a Qwiic connector and is an excellent solution for IoT projects. SparkFun WRL-18567
Function module designed for MicroMod boards. It allows you to add WiFi wireless communication based on the DA16200 chip to the project. SparkFun WRL-18594
WiFi 802.11 b/g/n module with ESP8266 system, 16 terminals are available with a 2 mm pitch with the possibility of soldering gold pins, there are 9 GPIO lines and 1 ADC line on the connector. Built-in ceramic antenna and U.FL antenna connector. ESP-07
WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E
No product available!
Development board ESP8266 with WiFi module; WRL-13231
Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05
WiFi module based on ESP8266. The module has a built-in antenna and USB-UART converter. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. 10 GPIO lines are available which each can be configured to work as PWM, I2C.
Arduino compatible shield for the ESP8266 WiFi SoC – a leading platform for Internet of Things (IoT) or WiFi-related projects. WRL-13287
No product available!
With an integrated ESP8266 WiFi controller this module is a one-stop shop for almost any Internet-connected project. Firmware can be developed in Arduino and uploaded over a simple, serial interface. WRL-13711
No product available!
Development board with dimensions and spacing compatible with Arduino Uno R3. It have built-in Wi-Fi ESP8266 module. The device is compatible with WeDOS D1, it can be programmed from the level of Arduino IDE
Easy to use app builder that allows users to add a variety of buttons, sliders, graphical displays and even RGB controllers to their phone. The SparkFun Blynk Board is specially designed to work with the ‘widgets’ within the Blynk mobile app to create your next IoT project. WRL-13794
LPT100 WiFi Module Mother Board
An integrated module combining WiFi, Bluetooth 4.0 and FM radio. It has derived SDIO, UART and PCM interfaces. Ampak AP6335
ESP8266 based Arduino board for ArduCAM mini camera modules while keeping the same form of factors and pinout as the standard Arduino UNO R3 board. ArduCAM B0082
No product available!
ArduCAM CC3200 UNO Board CC3200 UNO is full featured development board almost like a combination of CC3200 Launchpad plus CC3200CAMBOOST pack from TI while keeping exactly the same size as Arduino UNO and pin out. B0078
Comprehensive development platform for Espressif ESP32 a WiFi-compatible microcontroller and nearly 30 I/O pins. DEV-13907
Wifi module with ESPR8266 ESPRESSIF for communication in the 2.4 GHz band. It is powered by a voltage from 3 V to 3.6 V, available in an SMD enclosure. ESP-WROOM-02
The ESP32 WiFi and Bluetooth module has a dual-core 32-bit MCU that integrates WiFi HT40 and Bluetooth / BLE 4.2 technology. Designed for mobile devices and Internet of Things (IoT) applications. DFRobot TEL0111
Board with the DA16200 WiFi module. It is equipped with a Qwiic connector and is an excellent solution for IoT projects. SparkFun WRL-19696