Wi-Fi module SPWF01SC.11

Advanced IEEE 802.11b/g/n WiFi controller in the 2.4GHz band, providing versatility and easy integration with systems thanks to SPI, UART, SDIO and USB interfaces. The WiFi software in the module is pre-loaded, allowing easy updates, which increases flexibility and adaptation to various applications. Segger emPower WiFi Module - Redpine Signals RS9113 (2.4 GHz) (6.37.03.02)

WiFI 802.11 b/g/n module. Equipment includes, among others: LED diode, antenna, 8 pins with 2.54mm pitch (including 3 GPIO lines). Power supply: 3.3V.

Connect your Arduino-compatible to the Internet with this WiFi shield that features the FCC-certified ATWINC1500 module from Atmel. Adafruit 3653

A small evaluation board with nRF52840 (ARM Cortex-M4) and WiFi ESP32-D0WD module for projects related to Mesh networks. Adafruit 3997

Development board D1 Mini V3 with WiFi module ESP-8266 and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini V3.x

RN-171 Series 54 Mbps 2.4GHz SMT WiFly GSX 802.11 b/g Wireless LAN module, MICROCHIP, RoHS

An integrated module combining WiFi, Bluetooth 4.0 and FM radio. It has derived SDIO, UART and PCM interfaces. Ampak AP6335

Wifi module with ESPR8266 ESPRESSIF for communication in the 2.4 GHz band. It is powered by a voltage from 3 V to 3.6 V, available in an SMD enclosure. ESP-WROOM-02

Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD

Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05

Evaluation set for IoT applications. Rich set of equipment in such peripheral systems as WiFi, OLED display, headphones, microphone, sensors (temperature, humidity, motion, pressure) make it a complete tool that will be used in many projects. DFRobot DFR0512

With an integrated ESP8266 WiFi controller this module is a one-stop shop for almost any Internet-connected project. Firmware can be developed in Arduino and uploaded over a simple, serial interface. WRL-13711

Compact module for program-free data transmission from sensors to IoT platforms, designed to work with Gravity: Science Data Acquisition (SCI DAQ). With 2.4GHz operation, support for various power sources and auto-reconnection function, the module provides stability and reliability in smart classrooms, environmental monitoring, agriculture and automation. DFRobot TEL0180

WiFi module developed by AI-Thinker Co., Ltd with ESP8266 processor. Integrates a 32-bit MCU microcontroller with 80 MHz clock, RTOS support, Wi-Fi and antenna. The module supports the IEEE802.11 b / g / ni standard and has a complete TCP / IP protocol stack. AI-Thinker ESP-12S

Powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. Espressif ESP32-WROOM-32E 32MBit (4MB)

Miniature (25x40mm) WiFi b/g/n module for surface mounting with support for TCP and UDP protocols operating in standalone and access point modes. The module is equipped with UART and Ethernet interfaces, it is also possible to control GPIO lines. Powered by 3.3V