Raspberry Pi Radio Module 2 RMC20452T - radio module for Raspberry Pi microcontrollers

WiFi module based on ESP8266. It has an embedded antenna and 0.96 "OLED display. The module can be programmed in Lua (under NodeMCU firmware control) or in the Arduino IDE. Provides 12 GPIO lines.

E-Paper ESP8266 Driver Board is a universal driver board for e-Paper displays. The board is based on the WiFi ESP8266 module. e-Paper ESP8266 Driver Board

Wireless-BE200 is a modern Wi-Fi 7 network card with an M.2 E Key interface, offering high throughput across three frequency bands and Bluetooth 5.4 for versatile wireless connectivity. With advanced technologies such as MU-MIMO and WPA4, it is ideal for upgrading computers, development kits, and modern embedded systems with fast and secure network access.

WiFi/BLE module that supports both the 2.4 GHz and 5 GHz WiFi bands, as well as Bluetooth Low Energy (BLE 4.2) communication. It has a u.FL connector dedicated to connecting an external antenna and a connector with a 2.54 mm pitch, which greatly facilitates prototyping. Tibbo WA2000U

Wi-Fi module based on the ESP8266 system - simplicity of use (communication through UART, supports AT commands), 3.3V power supply, support for WPA / WPA2 encryption - these features make the EPS8266 module applicable anywhere, where reliable and effective data transmission. The module is not equipped with an antenna, it should be attached using the U.FL connector. ESP-05

SPWF01SC are intelligent Wi-fi modules. Thanks to the Plug-And-Play solution and the autonomous 802.11 b/g/n solution, the module has the ability to easily integrate the wireless function with existing or new products.

With an integrated ESP8266 WiFi controller this module is a one-stop shop for almost any Internet-connected project. Firmware can be developed in Arduino and uploaded over a simple, serial interface. WRL-13711

WiFI 802.11 b/g/n module. Equipment includes, among others: LED diode, antenna, 8 pins with 2.54mm pitch (including 3 GPIO lines). Power supply: 3.3V.

A WiFi overlay designed for the OpenMV camera that adds wireless internet connectivity. It is equipped with an ATWINC1500 WiFi module. SparkFun WRL-16776

WIFI-LPB100-A module Eval Kit enables UART data transmission via WiFi, ultra low power consumption, encrypted communication

Advanced IEEE 802.11b/g/n WiFi controller in the 2.4GHz band, providing versatility and easy integration with systems thanks to SPI, UART, SDIO and USB interfaces. The WiFi software in the module is pre-loaded, allowing easy updates, which increases flexibility and adaptation to various applications. Segger emPower WiFi Module - Redpine Signals RS9113 (2.4 GHz) (6.37.03.02)

Development board in Feather format equipped with AW-CU488. The module has an integrated WiFi wireless communication controller, LiPo charging circuit and Qwiic connector. SparkFun DEV-19957

ArduCAM CC3200 UNO Board CC3200 UNO is full featured development board almost like a combination of CC3200 Launchpad plus CC3200CAMBOOST pack from TI while keeping exactly the same size as Arduino UNO and pin out. B0078

The nRF7002 is a board that allows you to add Wi-Fi connectivity to the Nordic Thingy:53 development kit. It connects to the Thingy:53 edge connector and enables the development of Wi-Fi 6 applications for low-power applications. Nordic Semiconductors nRF7002-EB

Advanced IEEE 802.11b/g/n WiFi controller in the 2.4GHz band and IEEE 802.11a/b/g/n 5GHz, providing versatility and easy integration with systems thanks to SPI, UART, SDIO and USB interfaces. The WiFi software in the module is pre-loaded, allowing easy updates, which increases flexibility and adaptation to various applications. Segger emPower WiFi Module - Redpine Signals RS9113 (2.4 + 5 GHz) (6.37.03.01)

Wi-Fi bridge for short to medium-range network transmission. With the advanced iPoll 3 protocol and support for multiple services, it is ideal for various video surveillance scenarios. Its IP-66 rated housing ensures weather resistance