PYNQ-Z1 + Accessory Kit
ID: 576206
5906623491629
zł2,355.40
Tax included
zł1,914.96 tax excl.
Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with system image for PYNQ-Z1. Digilent 240-114-1
Description
Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with image for PYNQ-Z1.
PYNQ-Z1 is a programmable FPGA board for embedded systems that natively supports multimedia using on-board audio and video interfaces. The board has been designed to easily expand its capabilities with the help of Pmod modules, Arduino shields, Grove extensions, as well as using shared GPIO ports. The capabilities of the PYNQ-Z1 set can also be expanded using USB devices - such as Wi-Fi cards, Bluetooth modules or cameras.
Features
ZYNQ XC7Z020-1CLG400C:
- 650MHz dual-core Cortex-A9 processor
- DDR3 memory controller with 8 DMA channels and 4 high performance AXI3 slave ports
- High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
- Low-bandwidth peripheral controller: SPI, UART, CAN, I2C
- Programmable from JTAG, Quad-SPI flash, and microSD card
- Artix-7 family programmable logic
- 13,300 logic slices, each with four 6-input LUTs and 8 flip-flops
- 630 KB of fast block RAM
- 4 clock management tiles, each with a phase-locked loop (PLL) and mixed-mode clock manager (MMCM)
- 220 DSP slices
- On-chip analog-to-digital converter (XADC)
Memory:
- 512MB DDR3 with 16-bit bus @ 1050Mbps
- 16MB Quad-SPI Flash with factory programmed globally unique identifier (48-bit EUI-48/64™ compatible).
- MicroSD slot
USB and Ethernet:
- USB-JTAG Programming circuitry
- USB-UART bridge
- USB OTG PHY (supports host only)
- Gigabit Ethernet PHY
Audio and Video:
- Electret microphone with pulse density modulated (PDM) output
- 3.5mm mono audio output jack, pulse-width modulated (PWM) format
- HDMI sink port (input)
- HDMI source port (output)
Switches, push-buttons, and LEDs:
- 4 push-buttons
- 2 slide switches
- 4 LEDs
- 2 RGB LEDs
Expansion Connectors:
- Two standard Pmod ports
- 16 Total FPGA I/O
Arduino/chipKIT Shield connector:
- 49 Total FPGA I/O
- 6 Single-ended 0-3.3V Analog inputs to XADC
- 4 Differential 0-1.0V Analog inputs to XADC
Power:
- Powered from USB or any 7V-15V source (see recommended products)
Kit contains
- Development board PYNQ-Z1
- Micro USB cable
- Ethernet cable
- MicroSD card with pre-loaded PYNQ-Z1 boot image
- 12 V/3 A power supply
576206
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The board features a Zynq XC7Z020, Ethernet, HDMI in/out, MIC in, Audio out, Arduino Interface, 2 Pmods, 16 pin GPIO header, user LEDs, pushbuttons and Switches. 6003-410-0
zł1,212.60
24h
Available quantity: 1
Available
Other products in the same category (16)
Development kit with Xilinx Spartan 6 FPGA. Equipped with display, buttons, audio and video outputs and microSD slot. Numato Lab FPGA006
zł399.00
24h
Available quantity: 3
Available
FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3L SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1004-B
zł18,685.32
3 weeks
No product available!
Development kit with Xilinx Spartan-6 FPGA. Equipped with displays, buttons, audio and video outputs and a breadboard. Numato Lab WXDE001
zł1,642.09
3 weeks
No product available!
The Digilent Cmod A7 is a small, breadboard friendly 48-pin DIP form factor board built around a Xilinx Artix-7 FPGA. The board also includes a USB-JTAG programming circuit, USB-UART bridge, clock source, Pmod host connector, SRAM, Quad-SPI Flash, and basic I/O devices. 410-328
zł529.00
3 weeks
No product available!
FPGA development board with Xilinx Kintex-7 FPGA chip with 4 GB DDR3L SDRAM memory. Equipped with a fast USB 3.1 interface. Numato Lab NLFX1004-A
zł8,161.97
3 weeks
No product available!
Module with Xilinx Artix-7 35T, FLASH memory with 32 MB capacity. Everything fits on a small 4 x 5 cm tile. TE0711-01-35-2C
zł633.04
4 weeks
No product available!
Development kit with Xilinx Spartan-6 FPGA with built-in DDR memory and IO interface expansion connectors. The base board facilitates access to the FPGA IO. Numato Lab FPGA005
zł1,366.09
3 weeks
No product available!
FPGA Evaluation Kit based on the XC7A100T-1CSG324C chip from the Artix-7 FPGA Xilinx family. Nexys works with Xilinx ISE and Vivado software . Equipped with numerous interfaces and sensors allows you to develop projects without attaching additional elements to the set. Digilent 410-292
zł1,945.81
3 weeks
No product available!
Development kit with Artix-7 100T FPGA chip, compatible with the PC/104 standard. The set is equipped with 512 MB DDR3 memory, Zmod port and Pmod ports. Digilent 410-398
zł2,314.61
3 weeks
No product available!
A programming platform designed on the basis of the Xilinx system-on-chip system Zynq-7000 (APSoC). The Zynq-7000 architecture integrates the ARM Cortex-A9 667 MHz processor with the Xilinx 7 FPGA chip. Digilent Cora Z7-07S (410-370)
zł843.67
24h
Available quantity: 2
Available
Module with Xilinx Artix-7 35T system, 32MB FLASH memory and 8MB HyperRAM memory. TE0725-03-35-2C
zł490.88
4 weeks
No product available!
FPGA CPLD mother board, provides several I/O interfaces, supports various accessory boards
zł62.48
24h
Available quantity: 1
Available
Development kit with FPGA Artix-7 100T equipped with 512 MB DDR3 memory, Zmod port and Pmod ports and two-channel ADC Zmod Scope 1410-105 converter. Digilent 471-047
zł3,373.34
3 weeks
No product available!
Platform with the AD9364 radio transmitter and receiver and the Xilinx Spartan-6 XC6SLX75 FPGA chip. Digilent 6002-410-022
zł7,177.75
3 weeks
No product available!
Base plate for Trenz Electronic 4 x 5 cm modules. It allows you to connect an FPGA system through board-to-board connections to external peripherals to test and develop software. TE0701-06
zł1,985.36
4 weeks
No product available!
FPGA development board with Xilinx Artix-7 XC7A100T. Designed for a wide variety of applications. Numato Lab FPGA009-SS
zł2,457.75
3 weeks
No product available!
Development board FPGA PYNQ-Z1 and accessor set. Includes base plate, power supply, cables and SD card with system image for PYNQ-Z1. Digilent 240-114-1