Category: STARTER KITS, PROGRAMMERS, MODULES

3-axis motion sensor module with digital output

The KAmod ESP32 POW+RS485 board equipped with the ESP32-WROOM32D 4MB (32Mb) module supports 2.4 GHz Wi-Fi, RS485 communication, also has a USB-UART converter, an efficient power supply system and a 40-pin connector compatible with Raspberry Pi, making it an ideal solution for home and industrial automation

KAmod ESP32 ETH+POE is a board equipped with the ESP32-WROOM module, enabling communication via Wi-Fi 2.4 GHz and Ethernet with a typical RJ45 connector, integrated with a USB-UART converter and a PoE power supply system compliant with IEEE 802.3af/at. The design of the board with dimensions of 85x56 mm resembles the Raspberry Pi family, and on the 40-pin connector there are all important I/O ports and supply voltages of 5 V and 3.3 V for powering additional components

Kamod BluePill+ is a modern development board with STM32F103 microcontroller, equipped with SPI, I2C, UART interfaces, two 12-bit ADC converters and USB-C connector, ideal for creating projects based on ARM Cortex-M3 architecture

KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20

Module with 8 LEDs

9-axis expansion module with motion sensors. The module combines two integrated circuits: FXAS21002C 3-axis gyroscope and FXOS8700CQ 6-axis accelerometer/magnetometer. The board is equipped with connectors compatible with Arduino R3. NXP FRDM-STBC-AGM01

Audio module with 8 Ohm loudspeaker and 8002B amplifier. It can be used as a buzzer and also play high-quality sound. The volume is controlled by a potentiometer. DFRobot FIT0449

Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD

Board with WiFi and BLE Espressif ESP32-S3 module and OV2640 camera and digital microphone. It offers 8 MB Flash memory and 8 MB SRAM. It is equipped with a USB type C connector and a WiFi/BT antenna. Seeed Studio 113991115

A small development kit with a SAMD21 ARM Cortex M0 + microcontroller. There are 14 GPIO connectors on the board, including 11 digital and analog pins, 10 PWM, DAC, I2C, UART, SPI, SWD. Compatible with Arduino. Seeed Studio 102010328

KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05

Marcin. Bonds

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

Educational micro:bit module with 32-bit ARM Cortex-M4 microcontroller. Manufactured to interest the youngest in computer engineering. SparkFun DEV-17287

Jarosław Doliński

Simulation set for Siemens S7-1200 PLC devices. Using this set, it is possible to verify the operation of a program written for a PLC by applying the appropriate states to the digital inputs, to the analogue (ADC) inputs voltages from the built-in or external sensors. LED status monitoring is possible

Evaluation board kit with XMC1100 , Infineon, RoHS

The Coral USB Accelerator adds an Edge TPU coprocessor to your system, enabling high-speed machine learning inferencing on a wide range of systems, simply by connecting it to a USB port. Coral USB Accelerator