Category: STARTER KITS, PROGRAMMERS, MODULES

The X-NUCLEO-IKS02A1 industrial motion MEMS sensor expansion board is compatible with the Arduino UNO R3 connector layout. STMicroelectronics X-NUCLEO-IKS02A1

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

Module with three optical inspection sensors (spectrophotometers) from the AS7265x series. The module consists of three sensors; AS72651, AS72652 and AS72653 which can detect wavelengths from 410nm (UV) to 940nm (IR). SparkFun SEN-15050

Optical Time of Flight sensor with Pmod I2C connector. The built-in ISL29501 digital signal processor calculates the time it takes for the light emitted by ToF to reach the destination and back. The calculated time is proportional to the distance. Pmod ToF has a range of up to 5 m. Digilent 410-392

SparkFun weather: bit module designed for micro: bit, with temperature, humidity and pressure sensor (BME280 system). In combination with the micro: bit module, it is possible to build a fully functional weather station. SparkFun DEV-15837

Evaluation kit with Sparkfun Artemis Bluetooth 5.0 module designed on the basis of the Feather kit. It has a USB C. The board also has a USB-UART converter, a microphone and a JTAG debugging connector. Artemis has support in the Arduino IDE. SparkFun WRL-15574

Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605

Evaluation kit with RISC-V Dual Core 64bit chip and WiFi ESP32 chip. Equipped with a USB-UART converter, MEMS microphone, OV2640 camera and a microSD card slot. The set is compatible with Arduino UNO Rev3. Seeed Studio 102991184

Evaluation kit with STM32H7B3LIH6QU microcontroller with 2MB Flash memory and 1.4MB RAM memory. Equipped with a TFT display with a touch screen, WiFi module and numerous peripherals and connectors. STMicroelectronics STM32H7B3I-DK

Evaluation kit with the i.MX 8M Mini 4-core application processor. The set is equipped with a WiFi and Bluetooth 4.1 module and has Ethernet, USB 3.0 and PCIe M.2 interface. NXP 8MMINID4-EVK

Expansion board equipped with VL6180 distance sensor, based on FlightSense technology. The set is designed to measure distances and detect gestures. X-NUCLEO-6180A1

Development platform for the STM32L4P5AGI6PU microcontroller based on Arm Cortex-M4 core with I2C, SPI and USART, CAN, SAI, 12-bit ADC and DAC, Octo-SPI, USB OTG, LCD TFT controller and FMC. It has a built-in STLINK-V3E programmer. STMicroelectronics STM32L4P5G-DK

35 W offline LED driver for 4 channels HB RGGB LED based on L6562A.

GPS Receiver, Digilent, RoHS

Minicomputer with the SOM STM32MP157C. It has a dual-core Arm® Cortex®-A7 and an Arm® Cortex®-M4, as well as a PMIC power supply system, 512MB RAM and 4GB eMMC. The set consists of the SOM module and the base board. Seeed Studio 102110319

Experimenter Board with MSP430FR5739 MCU, TI, RoHS

Development board with ST Zio and ST morpho connectors, based on the STM32L552ZE microcontroller. Thanks to the built-in programmer compatible with ST-Link/v2-1, it is possible to program and debug the microcontroller via the USB connector. STMicroelectronics NUCLEO-L552ZE-P-Q

Development board with ST Zio and ST morpho connectors, based on the STM32H753ZI microcontroller. Thanks to the embedded STLINK-V3 programmer, it is possible to program and debug the microcontroller via USB. STMicroelectronics NUCLEO-H753ZI

The set consists of STM32 Nucleo NUCLEO-G431RB plate with STM32G431RB microcontroller, X-NUCLEO-IHM16M1 plate with three-phase STPIN830 BLDC / PMSM motor controller and GBM2804H-100T motor. STMicroelectronics P-NUCLEO-IHM03