Category: STARTER KITS, PROGRAMMERS, MODULES

Development kit based on Vybrid® VF61NS151CMK50 processor equipped with two cores: Cortex-A5 with frequency 500 MHz and Cortex-M4 with frequency 167 MHz. The module has a built-in memory DDR3 128 MB and Flash 256 MB. TWR-VF65GS10

Xplorer ++ Baseboard - development kit

Module with a gesture sensor PAJ7620U2, which allows to recognize up to 13 gestures. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020083

MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067

Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214

The SparkFun Roshamglo is the new and fun way to play Rock-Paper-Scissors with your friends! The board uses the ATtiny84, and has an IR LED and receiver to communicate between badges. KIT-14130

The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340

The board is equipped with ATSAMD21 microcontroller with ARM Cortex-M0 core and SPI Flash memory, GPIO pins and RGB diode. Adafruit 3505

Adafruit HUZZAH32 is a development board with a built-in WiFi ESP32 module. Processor frequency: 240 MHz, Li-Pol battery charging system. Adafruit 3405

Gravity: UART Infrared CO2 Sensor is a high precision CO2 sensor. It uses the UART interface for communication. It allows to measure CO2 content in the air in the range of 0 ... 50000ppm. DFRobot SEN0220

Module with ATSAMD21G18 microcontroller and 900 MHz wireless transceiver. The module can be used for transmission in the ISM 868 MHz band after the appropriate software configuration. The ATSAMD21G18 microcontroller (ARM Cortex-M0) is clocked at 48 MHz and operates at 3.3 V. Adafruit 3176

Gravity: Analog Infrared CO2 Sensor is a high precision analogue CO2 sensor. It measures CO2 content in the range of 0 ... 5000ppm and is compatible with all devices with ADC function. DFRobot SEN0219

The X-NUCLEO-53L0A1 expansion board features the VL53L0X ranging and gesture detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is an evaluation board that provides an introduction to the ranging and gesture detection capabilities of the VL53L0X module

Gravity: Voice Recorder Module is a sound recording module powered by 5V voltage. It can store sounds up to 10 seconds long. DFRobot SEN0197

Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191

Teensy Prop Shield is meant for making light and sound effects on small, handheld props and wearable costumes. This shield features a 2W audio amp, high-speed 5V buffers for driving APA102 LEDs, and an 8MB flash memory. PJRC PROP-SHIELD-LC

Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.