TFT LCD display with a diagonal of 3.5" and a resolution of 480x320 pixels. Equipped with a resistive touch panel and a microSD slot. Intended for use with Feather series boards. Adafruit 3651

DFRobot BLE4.1 Module is a Bluetooth 4.1 module with DA14681 processor with 3.3 V power supply. It is characterized by low energy consumption and advanced energy management system (built-in charging module). DFRobot TEL0120

The Arduino expansion board is dedicated to applications that use NB-IoT communication. Thanks to the GNSS (Global Navigation Satellite System) module, it supports GPS, GLONASS, Galileo, QZSS and BeiDou navigation systems. The module is supplied with the voltage from 7 to 12 V. DFRobot DFR0572

Camera module with Sony IMX219 sensor works with all versions of Raspberry Pi. The camera is equipped with a matrix with a resolution of 8 MPx, the maximum video resolution is 1080p. ArduCAM B0102

Module with 2 relays with a maximum switching current of 7 A. It communicates via the USB interface. Numato Lab RL20001

RGB LED strip driver module dedicated to Arduino boards. It can work with tapes with a supply voltage of up to 12 V and a current consumption of up to 3 A. DFRobot DFR0274

Module with an analog current sensor. Enables measurement of alternating and direct current up to 20 A. DFRobot SEN0214

Module with GNSS PA1616D receiver based on the MTK3333 chip. Supports GPS and GLONASS positioning systems. Adafruit 5440

This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758

The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435

Set (5 pieces) of wires for attaching modeling servos with the Grove system. With one wire you can connect 2 servos to one Grove slot. Seeed studio 110990057

Module with SSR relay with a load of up to 3 A. It communicates via the USB interface and does not require additional power supply. Numato Lab SSRP20001-AC

Data logger programmed to automatically record data from GPS and Qwiic series sensors. SparkFun DEV-19426

Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029

Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007

DC motor driver that allows you to control the movement of three drives using the I2C interface. Connectors for self-assembly. Pololu 5034

DC motor driver that allows you to control the movement of three drives using the I2C interface. Board with soldered connectors. Pololu 5033

5 mW red laser diode module displaying a point. It uses the PWM signal for control. It can be supplied with the voltage from 4.8 V to 5.2 V. Adafruit 1056

8x8 matrix or a 4-digit 7-segment display. Matrices like these are \'multiplexed\' - so to control all the seven-segment LEDs you need 14 pins. Adafruit 1002

Gamepad module (game controller) with joystick and buttons. Designed for Feather tiles. Adafruit 3632