Module with a slide potentiometer. Depending on the position of the slider, the resistance value (maximum resistance 10kΩ) changes, which translates into the voltage value at the analog output of the module. The module has a connector in accordance with the Grove standard. Seeed studio 101020036

The LSM6DS33 combines a digital 3-axis accelerometer and 3-axis gyroscope into a single package. The sensor provides six independent acceleration and rotation rate readings whose sensitivities can be set in the ranges of ±2 g to ±16 g and ±125°/s to ±2000°/s, available through I²C and SPI interfaces.

This compact Bluetooth AUX adapter with USB-C enables wireless audio streaming to traditional audio equipment, transforming any system into a modern wireless solution.

With an integrated ESP8266 WiFi controller this module is a one-stop shop for almost any Internet-connected project. Firmware can be developed in Arduino and uploaded over a simple, serial interface. WRL-13711

WIG-13720

DEV-13342

This kit includes four 16MP IMX519 cameras and a baseboard for the Raspberry Pi and NVIDIA Jetson AGX Orin, Orin Nano, and Orin NX platforms. The cameras are equipped with a Sony IMX519 sensor with autofocus that works in manual, automatic, and continuous modes, offering complete control over image sharpness. With single, dual, and quad modes, the kit is ideal for robotics, surveillance, and advanced computer vision systems, ensuring synchronization and high image quality. ArduCAM B0388

This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758

The module with a TA12-200 current sensor with a measuring range of alternating current up to 5 A. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020027

Module with a 3-axis KX132 accelerometer. The system has a user selectable measurement scale of ± 2/±4/±8/±16g. There are two Qwiic connectors on the board and holes with a 2.54 mm pitch. SparkFun SEN-17871

Set with a measuring module and a probe for measuring electrical conductivity. It allows you to measure the salinity of water and soil. It has a Gravity analog output interface. DFRobot DFR0300

USB adapter designed for XBee modules. It can be connected to a computer with a USB cable and used with the X-CTU software to configure the XBee. SparkFun WRL-11812

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

This module provides precise, galvanically isolated current measurement within a range of ±30 A and voltage up to 480 VRMS, providing RMS, instantaneous, and active, reactive, and apparent power readings. Equipped with an I²C interface, 4-pin JST SH connectors, and 2.54 mm pins, it allows for easy integration with Qwiic, STEMMA QT, and standard microcontrollers. Configuration stored in EEPROM allows for defining address and overload thresholds. The sensor offers three voltage measurement ranges (120 V - default, 240 V, 480 V RMS) and the ability to detect overvoltages. Built-in protection and low conduction resistance ensure safe and accurate measurements. The version comes with soldered screw terminals and a 240 Vrms jumper. Pololu 5412

The HDMI-HDMI 8K 1.5 m cable by BLOW is a high-quality cable supporting resolutions up to 8K at 60 Hz and 4K at 144 Hz, ensuring excellent image and sound quality. With gold-plated connectors and a triple-layer shield, the cable offers durability and resistance to interference, making it ideal for use with consoles, computers, and televisions.

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

LoRa module working on the 868 MHz frequency band with built-in RP2040 microcontroller, CH340 USB to UART converter, 74HC125V voltage level converter. SB Components 23240

TFT LCD driver with DPI interface dedicated to Raspberry Pi. It allows you to operate resistive touch panels. Adafruit 2453

The SanDisk Ultra microSDHC 256GB 150MB/s C10 Memory Card with Adapter is a high-capacity, efficient, and reliable storage device offering fast data transfer, compatibility with various devices, and durability in challenging conditions. Perfect for smartphones, tablets, action cameras, and drones.

The STN 128×64 display in negative blue mode with a TOSHIBA T6963C controller enables easy control of graphics and text. Thanks to its extended temperature range and LED backlight, it is suitable for industrial, mobile, and devices operating in variable environmental conditions.