Category: Main categories

X-NUCLEO-IDS01A5 is a development board STM32 Nucleo that allows you to use the RF SPSGRF-915 module on the ISM band (915 MHz carrier).

Sewable with a 3-pin JST wiring adapter with 3 holes on the board perfect for conductive thread or soldering, wired to a single 3-pin JST-PH Adapter. Sdafruit 2566

The driver with the TPIC6C596 system allows you to control 7-segment displays using three signal lines. Serial connection of controllers is possible. SparkFun WIG-13279

Bluetooth 2.1+EDR module for mounting in SMD technology with a fully configurable UART interface (transfer speed up to 2 Mb/s). SparkFun WRL-12575

32-bit microcontroller from the STM32F4 family with ARM Cortex-M4 core, 1024kB Flash memory, 192kB RAM, 168MHz, CAN, I2C, IrDA, LIN, SPI, UART / USART, USB OTG, Brown-out Detect / Reset, DMA, I2S, LCD, POR, PWM, WDT, 1.8 ... 3.6 V, A / D 16x12b, D / A 2x12b, 100-LQFP

Intermediate Kit for Arduino V2, The Arduino beginner kit - KIT0018

Recognizes the distance of an object away from the sensor up to about 10 inches (~25cm) and the location of the object from side to side across the sensor in about a 6 inch (~15cm) span. You will be able to use I2C or UART to communicate with the ZX Sensor via an Arduino-based microcontroller as well as a computer. SEN-12780

hb01w-b-220-08

Hybrid bipolar stepping motor with integrated 38cm (15″) threaded rod as its output shaft, turning it into a linear actuator capable of precision open-loop positioning. The motor has a 1.8° step angle (200 steps/revolution) and each phase draws 1.7A at 2.8V, allowing for a holding torque of 3.7kg-cm (51 oz-in). Pololu 2690

Module with a stepper motor driver based on the DRV8825 system. allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage up to 45 V. Pololu 2987

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.8″, but it allows a typical continuous output current of up to 5 A. Typical efficiencies of 85% to 95% make this regulator well suited for high-power applications like powering motors or servos.

Step-Down Voltage Regulator D24V25F5. Pololu 2850

The compact (0.4″ × 0.5″) D24V5F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while allowing for a maximum output current of 500 mA. Pololu 2845

The compact (0.4″ × 0.5″) D24V5F2 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 2.5 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

The compact (0.4″ × 0.5″) D24V5F1 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 1.8 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 75% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

Kit for building a minisumo robot on a crawler chassis. It has a bulldozer, control board and a set of caterpillars. Robot version for self-assembly, requires additional motors, Arduino controller and four AA batteries. Pololu 2509

32-bit STM32F2 microcontroller with ARM Cortex-M3 core, 1MB Flash memory, 132kB RAM, 120MHz, CAN, Ethernet, I2C, IrDA, LIN, Memory Card, SPI, UART / USART, USB OTG, Brown-out Detect / Reset, DMA, I2S, LCD, POR, PWM, WDT, 1.8 ... 3.6 V, A / D 24x12b; D / A 2x12b, 100-LQFP

Digital oscilloscope equipped with a 7" TFT LCD display. It has four measurement channels with a 50 MHz bandwidth, a sampling rate of 1 GSa/s and a 24 Mpts memory buffer. Rigol DS1054Z

Complete Robot Kit with Romeo V2 All-in-one controller, Sharp GP2Y0A21 Distance Sensor, 9g micro servo which allow you to install sensors, servos and even do some prototypings. KIT0071

Touch screen (capacitive panel) 2.8 "(320 x 240 pixels) designed for Raspberry Pi A / B. The display is controlled by the SPI interface. Adafruit 1983