Arduino Nano RP2040 Connect - board with RP2040 microcontroller
search
  • Arduino Nano RP2040 Connect - board with RP2040 microcontroller
  • Arduino Nano RP2040 Connect - board with RP2040 microcontroller
  • Arduino Nano RP2040 Connect - board with RP2040 microcontroller
  • Arduino Nano RP2040 Connect - board with RP2040 microcontroller
ID: 586418
7630049203051
zł139.00
Tax included

zł113.01 tax excl.

Arduino development board with RP2040 microcontroller. Equipped with WiFi and Bluetooth module, 6-axis IMU system with accelerometer and gyroscope, MEMS microphone, RGB LED diode and cryptographic system. Arduino ABX00052

24h
Available
Available quantity: 21
Kamami is the official distributor of Arduino development kits and accessories. All boards of this brand in our offer are original and come directly from the manufacturer.

Description

Development board from the Arduino family equipped with the RP2040 microcontroller designed by the Raspberry Pi foundation. The system has two ARM Cortex M0+ cores operating at a frequency of 133 MHz and 264 KB of RAM. The microcontroller is not equipped with flash memory, but on the board there is an external memory with a capacity of 16 MB connected via the QSPI interface.

On the board, apart from the RP2040 system and Flash memory, the user will find the U-blox Nina W102 module with WiFi and Bluetooth communication, a 6-axis IMU system with an accelerometer and a gyroscope, a MEMS microphone, an RGB LED diode, a cryptographic system and derived microcontroller connectors, including 14 digital pins, 8 analog inputs, UART, SPI, I2C interfaces and a microUSB connector.

The board can be programmed using the Arduino IDE offline or in the Arduino IDE Cloud online. For programming, you can use a microUSB connector or a wireless connection using the cloud.

Features

  • Raspberry Pi RP2040 microcontroller
    • 133 MHz, 32-bit, dual-core Arm® Cortex®-M0+
    • 264 kB of on-board SRAM
    • DMA controller
    • Supports up to 16 MB of external Flash memory via the dedicated QSPI bus
    • USB 1.1 and PHY controller, with host and device support
    • 8 PIO
    • Programmable IO (PIO) for extended peripheral support
    • 4-channel ADC converter with internal temperature sensor, 0.5 MSa / s, 12-bit conversion
    • Debugging SWD
    • 2 built-in PLL for generating USB clock and core
    • 40 nm process
    • Support for low-power modes
    • USB 1.1 host and device
    • Internal voltage stabilizer
    • Advanced AHB and Peripheral Bus (APB)
  • U-blox® Nina W102 WiFi and Bluetooth module
    • 240 MHz, 32-bit, dual-core Xtensa LX6
    • 520 kB SRAM
    • 448 KB ROM for startup and basic functions
    • 16 Mbit Flash
    • 1 kbit EFUSE (non-removable memory) for MAC addresses, module configuration, FlashEncryption and Chip-ID
    • IEEE 802.11b/g/n Wi-Fi 2.4 GHz
    • Bluetooth 4.2
    • Integrated planar PIFA antenna
    • 4 x 12-bit ADC
    • 3 x I2C, SDIO, CAN, QSPI
  • Memory
    • AT25SF128A 16MB NOR Flash
    • QSPI data transfer rate up to 532 Mb/s
    • 100K programming cycles
  • 6-axis IMU ST LSM6DSOXTR
    • 3D gyroscope with a measuring range of ± 2, ± 4, ± 8, ± 16 g of full scale
    • 3D accelerometer with a measuring range of ± 125, ± 250, ± 500, ± 1000, ± 2000 dps in full scale
    • Advanced pedometer
    • Motion detection, tilt detection
    • Standard interrupts: free fall, 6D / 4D orientation, impact and double click
    • Programmable finite machine: accelerometer, gyroscope and external sensors
    • Machine Learning Core
    • Built-in temperature sensor
  • ST MP34DT06JTR MEMS microphone
    • AOP = 122.5 dBSPL
    • 64 dB signal-to-noise ratio
    • Omni-directional sensitivity
    • -26 dBFS ± 1 dB sensitivity
  • RGB LED
    • Common anode
    • Connected to the U-blox® Nina W102 GPIO
  • Microchip® ATECC608A Crypto
    • Cryptographic coprocessor with hardware-secure key storage
    • I2C, SWI
    • Hardware support for symmetric algorithms:
      • SHA-256 and HMAC Hash, including save and restore context
      • AES-128: encryption and decryption, Galois field multiplication for GCM
    • Internal high quality random number generator NIST SP 800-90A / B / C (RNG)
    • Secure Boot Support:
      • Full validation of the ECDSA code signature, optionally stored hash, signature
      • Optional disabling of the communication key before safe startup
      • Message encryption and authentication to prevent attacks
  • I/O
    • 14 x digital pin
    • 8 x analog pin
    • Micro USB
    • Support for UART, SPI, I2C
  • Power supply: Step-Down converter
586418

Data sheet

Microcontroller
RP2040
Core
Cortex-M0+
Frequency
133 MHz
Flash memory
16 MB
RAM
520 kB
EEPROM memory
none
Number of digital pins
14
Number of PWM channels
20
Ilość wejść analogowych
8
ADC
4x 12bit
DAC
none
CAN
none
USB
1
Ethernet
none
WiFi/BT module
Yes
Bluetooth module
Yes
GSM/GPRS module
No
Logic voltage
3,3 V
MicroSD slot
No
Supply voltage min
3,3 V
Supply voltages max
5 V

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

You might also like

Other products in the same category (16)