zł31.95 tax excl.
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
The high power motor controller module allows you to control the motor with a current consumption of up to 43 A. The board has a small size, is equipped with a heat sink and screw connections. H-bridge systems are protected against short-circuit, overload or overheating. The module can be controlled from the level of Arduino, Raspberry Pi, STM. Operating voltage range: 5.5-27 V.
| Contact | Name | Description |
|---|---|---|
| 1 | RPWM | Engine control signal in R direction (PWM or level) |
| 2 | LPWM | Engine control signal in direction L (PWM or level) |
| 3 | RHENIUM | Signal of work permit in the direction of R |
| 4 | FLAX | Work permit signal in the L direction |
| 5 | R_IS | Alarm output (R) |
| 6 | L_IS | Alarm output (L) |
| 7 | VCC | Power input buffer (3.3-5.5 V) |
| 8 | GND | Mass |
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pololu High-Power Motor Driver 18v25 CS
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5056
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5055
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5054
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5053
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5051
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5050
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5049
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
No product available!
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
Module with a DC motor driver based on the MC33886 chip. It allows you to control the movement of drives with a working voltage from 5 to 28 V and a current of up to 5 A
No product available!
TB6612FNG dual DC motor controller module. It can be used as a stepper motor driver or solenoid driver. Adafruit 2448
No product available!
Module with the HR1124S DC motor controller with a maximum current of 1.2 A. It can be powered with the voltage from 1.8 V to 6.8 V and is controlled by two PWM signals
A two-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. Board with connectors for assembly. Pololu 5067
No product available!
A two-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. Board with soldered connectors. Pololu 5066
No product available!
A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with connectors for mounting. Pololu 5065
No product available!
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2