

4-channel input selector for audio amplifier. It is equipped with RCA connectors and is controlled by a rotary switch connected to the selector plate with a tape. It allows you to select one of the signal sources fed to the selector inputs, which is sent to the output. The currently selected source is signaled by one of the LEDs on the switch board. The module is powered with AC voltage in the range from 12 to 15 V. It will be used in the projects of audio players.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The Class D digital audio amplifier module has two channels with a power of 15 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
Audio amplifier module with three output channels. It can be powered with the voltage from 12 to 24 V and has two outputs with a power of 50 W (left and right) and one with a power of 100 W (bass)
Audio amplifier based on the TPA3116 chip with a power of 100 W with an active low-pass filter. Dedicated to the bass column (subwoofer)
No product available!
4-channel input selector for audio amplifier. Equipped with terminal connectors and controlled by a rotary switch
No product available!
The module with a digital stereo audio amplifier is equipped with Bluetooth communication. The system allows you to connect two speakers with an impedance from 4 Ω to 8 Ω and a power of 15 W per channel
No product available!
MEMS SPU0414HR5H-SB analog microphone module. The board is equipped with a Grove connector and communicates via an analog interface. Seeed Studio 101020852
No product available!
Module with audio amplifier and 8 Ω speaker with a power of 1 W. The board is equipped with a STEMMA connector. Adafruit 3885
Class D PAM8406 stereo digital audio amplifier module. The system allows you to connect two speakers with an impedance of 4 to 8 Ω and a power of 5 W per channel
No product available!
Stereo audio amplifier based on the TPA3116D2 chip. It can be powered from 12 to 26 V and has two 120 W outputs. XH-M543
A module with an electret microphone, amplifier and ADC converter dedicated to micro: bit. It communicates via the I2C interface. SparkFun SEN-15289
Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475
The Class D digital audio amplifier module has two channels with a power of 15 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
Audio receiver with Bluetooth 5.0 communication based on the QCC3008 module. It can be powered with the voltage from 3.6 V to 5.5 V, including with a lithium battery
No product available!
TPA3110 digital stereo audio amplifier module. The system allows you to connect two speakers with an impedance from 4 Ω to 8 Ω and a power of 15 W
Module with MEMS microphone; model SPW2430 with built-in amplifier. The plate also has a 3.3 V voltage stabilizer needed to power the microphone. Adafruit 2716
Bluetooth 4.2 audio receiver with 3.5 mm jack audio output. It allows you to play files via Bluetooth and supports WAV, WMA APE, MP3 and FLAC formats. MH-M28
Bluetooth audio receiver module enclosed in a housing that enables wireless transmission of sounds. It is equipped with a PCB antenna, microphone, 3.5 mm audio jack and control buttons
Two-way speaker crossover with a division frequency of 3800 Hz. Works with 5 to 8 ohm speakers and offers up to 120 watts of power
No product available!
The board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Adafruit 1752
4-channel input selector for audio amplifier. Equipped with RCA connectors and controlled by a rotary switch